781858
22
Zoom out
Zoom in
Previous page
1/112
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
22 | GB
4. Fasten the guards (E + F) together using two
Phillips head screws, clamping brackets and nuts.
m IMPORTANT!
You must fully assemble the appliance before using it
for the rst time!
10. Initial operation
Make sure the machine is completely and expertly as-
sembled. Check before every use:
the connection cables for any defective spots
(cracks, cuts etc.).
the machine for any possible damage.
the rm seat of all bolts.
the hydraulic system for leakage.
the oil level and
the safety devices
10.1 Checking the oil level (Fig. 17)
The hydraulic unit is a closed system with oil tank, oil
pump and control valve. Check the oil level regularly
before every use. Too low an oil level can damage the
oil pump. The correct oil level is approx. 10 to 20 mm
below the oil tank surface.
If the oil level is at the lower notch, then the oil level is
at a minimum. Should this be the case, oil must be im-
mediately added. The upper notch indicates the max-
imum oil level. The machine must be on level ground.
Screw in the oil dipstick fully, to measure the oil level.
10.2 Ventilation screw
Before operating your machine, the bleed screw (7)
should be loosened by some rotations until air can go
in and out of the oil tank smoothly. Failed to loosen the
bleed screw will keep the sealed air in hydraulic sys-
tem being compressed after being decompressed.
Such continuous compression/decompression will
blow out the seals of the hydraulic system and cause
permanent damage to your machine.
Before moving your machine, make sure the bleed
screw is tightened to avoid oil leaking from this point.
10.3 Splitting logs
Only split logs that have been sawn off straight. To do
this, proceed as follows:
1. Place the log plain onto the work table (9).
2. Your machine is equipped with Two-hands Control
System that requires to be operated by both hands
of the user left hand controls the control lever (12)
while right hand controls the push button switch (6).
3. Simultaneously push button switch (6) to start the
splitting action.
The log splitter will freeze upon absence of either
hand.
3. Place the device horizontally on the oor, and put
the Styropor pad of the packaging underneath the
splitting wedge side.
4. Assemble the wheels on the wheel axis of the
stand.
9.2 Installing the handle (4) (enclosed accessories
bag a) (g. 5)
Fasten the handle to the U-bar with two cylindrical
screws.
9.3 Installing the protective guard (L) (enclosed
accessories bag b) (g. 6 + 7)
1. Fit the protective guard (L) to the trunk guide plate
(5) and use the enclosed cylindrical screws and
nuts to afx it.
2. Undo the cylindrical screw with washer that is lo-
cated on the wheel bracket.
3. Fasten the other end of the strut to the protective
guard using the Phillips head screw and nut. (3)
4. Now guide the open end of the strut (O) between
the washer and the wheel bracket, tighten the cy-
lindrical screw (4) again rmly.
9.4 Installing the tray table (K + M) (enclosed ac-
cessories bag c + d + e) (g. 8 + 9 + 10)
1. Attach the tray table (K) to the same side as the
protective guard (L). Use two cylindrical screws
and spring washers to afx the table to the log
splitter. (1)
2. Ensure that the table and the protective guard are
level in relation to each other.
3. Undo the screw on the left of the foot.
4. Fasten the other end of the strut to the protective
guard using the Phillips head screw and nut, align
everything and tighten the screws rmly.
5. Now guide the open end of the strut (N) between
the screw and the foot bracket, tighten the screw
slightly.
6. Repeat the process on the other side.
7. Align both tables in relation to each other and use
the Phillips head screws and nuts (e) to afx them.
9.5 Installing the guard (E - J) (enclosed
accessories bag f) (g. 11 + 12)
1. Connect the guards (H) and (I) together, use two
Phillips head screws, clamping brackets and nuts
to afx it.
2. Fasten the guards (H, I, J) to the holes provided
for this. These are on the side of the table and
the protective guard. Fasten the guard with seven
Phillips head screws, clamping brackets and nuts.
Fit the protective guard (G) to the control lever
protection (11) and use a Phillips head screw and
a nut to afx it.
3. Now fasten the guards (E + F) on the top. Fasten
them with eight Phillips head screws, clamping
brackets and nuts.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HL660 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HL660 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 5.23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info