Manual Scheppach HL650 (page 15 of 152) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish)

781961

Zoom out

Zoom in

1/152

Damaged electrical connections

Often, insulation damages occur on electrical connec-

tion lines.

The possible causes are:

• Drag marks if connection lines are led through window

or door clearances.

• Kinks due to improper attachment or routing of the

connection line.

• Cuts caused by running over the connection line.

• Insulation damages caused by pulling the connection

line out of the wall socket.

• Fissures caused by the aging of the insulation.

Such defective electrical connection lines must not

be used and are, due to the insulation damages, life

threatening!

Single phase motor 230 V/50 Hz

• The supply voltage must be 220-240 V/50 Hz.

• The mains connection and extension cable must have

3 wires = P+N+SL.–(1/N/PE).

• Extension lines up to a length of 25 m must have a

minimum cross section of 1.5 mm², lines with a length

exceeding 25 m must have a minimum cross section

of 2.5 mm².

• The mains connection is protected with a maximum

of 16 A.

The product meets the requirements of EN 61000-3-11

and is subject to special connection conditions. This

means that use of the product at any freely selectable

connection point is not allowed.

• Given unfavorable conditions in the power supply the

product can cause the voltage to uctuate temporarily.

• The product is intended solely for use at connection

points that

a) do not exceed a maximum permitted supply imped-

ance “Z”, or

b) have a continuous current-carrying capacity of the

mains of at least 100 A per phase.

• As the user, you are required to ensure, in consulta-

tion with your electric power company if necessary,

that the connection point at which you wish to operate

the product meets one of the two requirements, a) or

b), named above.

Use a portable di󰀨erential circuit breaker (PRCD) if the

RCD of the power supply is not intended for a maximum

rated trip current of 0.03 A.

The maximum variation of the power source shall not

exceed ± 10% of the nominal current and the maximum

frequency variation in the network shall not exceed ± 1%

of the nominal frequency.

Lignes de branchement électrique défectueuses

L’isolement des lignes de branchement électrique est

souvent endommagé.

Causes possibles :

• Empreintes lorsque les lignes de branchement sont po-

sées à travers des fentes de fenêtre ou de porte.

• Plis suite à une xation ou une pose inadéquate de la

ligne de branchement.

• Coupures suite à l’écrasement de la ligne de branche-

ment.

• Dommages d‘isolement suite à un arrachement pour sor-

tir la ligne de branchement de la prise de courant murale.

• Fissures suite au vieillissement de l’isolation.

Il est interdit d’utiliser de telles lignes de branche-

ment électrique endommagées. Et elles présentent

un danger de mort à cause des dommages sur l’iso-

lement.

Moteur à courant alternatif

• La tension de secteur doit être de 220–240 V / 50 Hz.

• Le câble de branchement au secteur et la rallonge

doivent avoir 3 brins = P+N+SL.–(1/N/PE).

• Des rallonges d’une longueur max. de 25 m doivent

avoir une section moyenne de 1,5mm et pour des ral-

longes de plus de 25 m la section moyenne doit être

de 2,5 mm.

• Le branchement au secteur est protégé par fusible de

16 A au maximum.

Le produit répond aux exigences de la norme EN 61000-

3-11 et est soumis à des conditions de raccordement

spéciales. Autrement dit, il est interdit de l’utiliser sur un

point de raccordement au choix.

• L’appareil peut entraîner des variations de tension pro-

visoires lorsque le réseau n’est pas favorable.

• Le produit est exclusivement prévu pour l’utilisation

aux points de raccordement

a) qui ne dépassent pas une impédance de réseau

maximale autorisée de «Z» ou

b) qui ont une intensité admissible du courant perma-

nent d’au moins 100 A par phase.

• En tant qu’utilisateur, vous devez vous assurer, si

nécessaire en consultant votre entreprise d’électricité

locale, que le point de raccordement avec lequel vous

voulez exploiter le produit, répond à l’une des deux

exigences a) ou b).

Utilisez un disjoncteur di󰀨érentiel portable (PRCD) si le

disjoncteur di󰀨érentiel (RCD) du réseau électrique n’est

pas prévu pour un courant nominal de déclenchement

maximal de 0,03 A.

La variation maximale de la source d’alimentation élec-

trique ne doit pas dépasser la valeur de ± 10% du cou-

rant nominal, et la variation maximale de fréquence

dans le réseau ne doit pas dépasser la valeur de ± 1%

de la fréquence nominale.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HL650 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 5.8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HL650 Manual

Product: