Manual Scheppach HL460 (page 22 of 112) (English, German, French, Italian)

781851

Zoom out

Zoom in

1/112

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

22 | GB

4. Fasten the guards (E + F) together using two

Phillips head screws, clamping brackets and nuts.

m IMPORTANT!

You must fully assemble the appliance before using it

for the rst time!

10. Initial operation

Make sure the machine is completely and expertly

assembled. Check before every use:

• the connection cables for any defective spots

(cracks, cuts etc.).

• the machine for any possible damage.

• the rm seat of all bolts.

• the hydraulic system for leakage.

• the oil level and

• the safety devices

10.1 Checking the oil level (Fig. 15)

The hydraulic unit is a closed system with oil tank, oil

pump and control valve. Check the oil level regularly

before every use. Too low an oil level can damage

the oil pump. If the oil level is at the lower notch, then

the oil level is at a minimum. Should this be the case,

oil must be immediately added. The upper notch in-

dicates the maximum oil level. The machine must

be on level ground. Screw in the oil dipstick fully, to

measure the oil level.

10.2 Ventilation screw

Before operating your machine, the bleed screw (7)

should be loosened by some rotations until air can go

in and out of the oil tank smoothly. Failed to loosen the

bleed screw will keep the sealed air in hydraulic sys-

tem being compressed after being decompressed.

Such continuous compression/decompression will

blow out the seals of the hydraulic system and cause

permanent damage to your machine.

Before moving your machine, make sure the bleed

screw is tightened to avoid oil leaking from this point.

10.3 Splitting logs

Only split logs that have been sawn o󰀨 straight. To do

this, proceed as follows:

1. Place the log plain onto the work table (9).

2. Your machine is equipped with Two-hands Con-

trol System that requires to be operated by both

hands of the user – left hand controls the control

lever (12) while right hand controls the push but-

ton switch (6).

3. Simultaneously push button switch (6) to start the

splitting action.

The log splitter will freeze upon absence of either

hand.

9. Attachment / Before starting the

equipment

At least two people are required to install the

device.

9.1 Installing the handle (4) (enclosed accesso-

ries bag a) (g. 3)

Fasten the handle to the U-bar with two cylindrical

screws.

9.2 Installing the protective guard (L) (enclosed

accessories bag b) (g. 4 + 5)

1. Fit the protective guard (L) to the trunk guide plate

(5) and use the enclosed cylindrical screws and

nuts to a󰀩x it.

2. Undo the cylindrical screw with washer that is lo-

cated on the wheel bracket.

3. Fasten the other end of the strut to the protective

guard using the Phillips head screw and nut. (3)

4. Now guide the open end of the strut (O) between

the washer and the wheel bracket, tighten the cy-

lindrical screw (4) again rmly.

9.4 Installing the tray table (K + M) (enclosed ac-

cessories bag c + d + e) (g. 6 + 7 + 8)

1. Attach the tray table (K) to the same side as the

protective guard (L). Use two cylindrical screws

and spring washers to a󰀩x the table to the log

splitter. (1)

2. Ensure that the table and the protective guard are

level in relation to each other.

3. Undo the screw on the left of the foot.

4. Fasten the other end of the strut to the protective

guard using the Phillips head screw and nut, align

everything and tighten the screws rmly.

5. Now guide the open end of the strut (N) between

the screw and the foot bracket, tighten the screw

slightly.

6. Repeat the process on the other side.

7. Align both tables in relation to each other and use

the Phillips head screws and nuts (e) to a󰀩x them.

9.5 Installing the guard (E - J) (enclosed

accessories bag f) (g. 9 + 10)

1. Connect the guards (H) and (I) together, use two

Phillips head screws, clamping brackets and nuts

to a󰀩x it.

2. Fasten the guards (H, I, J) to the holes provided

for this. These are on the side of the table and

the protective guard. Fasten the guard with seven

Phillips head screws, clamping brackets and nuts.

Fit the protective guard (G) to the control lever

protection (11) and use a Phillips head screw and

a nut to a󰀩x it.

3. Now fasten the guards (E + F) on the top. Fasten

them with eight Phillips head screws, clamping

brackets and nuts.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HL460 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 4.91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HL460 Manual

Product: