781661

Scheppach HG34 Manual

21
Zoom out
Zoom in
Previous page
1/124
Next page
21GB
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
7. Before putting the machine into
operation
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
Pull the power plug before doing any maintenance
or assembly work on the equipment.
• The machine must be set up so that it stands rmly,
i.e. it must be securely screwed to a work bench or
similar.
• All covers and safety devices have to be properly t-
ted before the equipment is switched on.
• The grinding and polishing wheel must rotat freely.
• Check that the voltage on the rating plate is the
same as your supply voltage before you connect the
equi ment to the power supply.
7.1 Fitting the spark re ector (Fig. 2-4 / Item 3)
Fit the spark re ector (3) to the double wheel grinder
using the adjusting screw (10).
7.2 Adjusting the spark re ector (Fig. 5 / Item 3)
• Adjust the spark deector (3) using the adjusting
screw (10) so that the distance between the dry
grinding wheel (5) and the spark deector (3) is as
small as possible and certainly does not exceed 2
mm.
• Adjust the spark deector (3) periodically to com-
pensate for wear on the wheel.
7.3 Fitting the workpiece supports (Fig. 6 / Item 8)
Secure the workpiece supports (8) to the double wheel
grinder using the star screw (7).
7.4 Adjusting the workpiece supports (Fig. 7 / Item 8)
• Adjust the workpiece supports (8) using the star
screws (7) so that the distance between the dry
grinding wheel (5) and the workpiece support (8) is
as small as possible and certainly does not exceed
2 mm. • Adjust the workpiece supports (8) periodi-
cally to compensate for wear on the dry grinding
wheel (5).
7.5. Changing the wheels (Fig. 8-9)
• Remove the 3 screws (A) holding the side section
of the safety hood (B) and remove the safety hood.
Slacken the nut (D) (Important: The grinding wheel
on the left is fastened with a lefthanded thread and
the grinding wheel on the right with a right-handed
thread) by holding the nut of the grinding wheel
mount on the opposite side.
• Then remove the  ange (C) and replace the grind-
ing wheel (5). To assemble, proceed in the reverse
order. The grinding wheel is mounted with the help
of a rag. Mount the  ange (C) and the nut (D) on
the shaft and hold steady with the help of a rag
when you tighten the nut (D).
6. TECHNICAL DATA
HG34
Mains voltage 230 V ~ 50 Hz
Power rating 120 W
Idle speed n00-9900 min-1
Grinding wheel
diameter 75 mm
Polishing wheel
diameter 75 mm
Wheel thickness 20 mm
Wheel hole diameter 10 mm
Max. peripheral
speed 50 m/s
Protection class II
Weight 3.1 kg
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
LpA sound pressure level ..................... 75,8 dB(A)
KpA uncertainty .............................................3 dB
LWA sound power level ....................... 88,7 dB(A)
KWA uncertainty .............................................3 dB
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with EN 61029.
Vibration emission value ah ≤ 2.5 m/s2
K uncertainty = 1.5 m/s2
Warning!
The speci ed vibration value was established in ac-
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the speci ed value in excep-
tional circumstances.
The specied vibration value can be used to compare
the equipment with other electric powertools.
The specied vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a
minimum.
• Only use appliances which are in perfect working-
order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
GB
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HG34 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HG34 in the language / languages: English, German, Dutch, French, Italian, Polish, Swedish, Norwegian as an attachment in your email.

The manual is 4.98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info