781454
19
Zoom out
Zoom in
Previous page
1/120
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
19 / 120
Remaining hazards can be minimized by following
the instructions in “Safety Precautions”, “Proper
Use“ and in the entire operating manual.
Keep this safety information in a safe place.
6. Technical data
Technical Data
Dimensions L x W x H
(mm): 1075 x 680 x 1800
Overall height with
lter bag mm 1800
Ectractor duct
connections ø mm 140
Hose length mm 2000
Approx. weight kg 44
Rate of air ow m3/h 2000
Pressure differential
Pa 1600
Filter aera (lter bag)
m2 ca. 1,6
Sawdust bag capacity
litres 130
Performance
Electric motor 220-240 V / 50 Hz
Nominal input P1 1,1 kW
Output power P2 0,6 kW
Motorspeed 1/min. 2800
Work Place Emissions Values:
Empty Run Noise dB
(A) 96
Working Noise dB (A) 76
7. Assembly
For packaging reasons your machine is delivered in
semi-assembled state.
Using the screws and nuts supplied, screw together
parts A, B and C of the cladding as shown in Figure
2+3.
Mount the axle and rollers on the base plate with
the screws and nuts, see Figure 4+5. Then set the
chassis on the wheels.
Screw the side parts D and E of the cladding toge-
ther in the middle using 3 screws and 3 nuts. (Fi-
gure 6+7)
Fasten the screwed parts A, B, C to the side clad-
ding (D, E), see Figure 8+9.
Set the fully assembled cladding on the base plate
of the chassis and fasten this using 4 screws and 4
nuts. (Figure 10)
Position the housing with motor on the cladding and
screw it tight using the screws and nuts. (Figure
11+12)
Slide the clamping strip through the loops on the
lter bag.
Insert the retainer rod in the housing and hang the
lter bag over it, then fasten the lter bag to the con-
tainer using the clamping strip (Figure 13+14).
Note the information published by your professio-
nal associations.
Do not use any low-powered machines for heavy
duty work.
Do not mis-use the cable
Make sure you stand squarely and keep your ba-
lance at all times.
Check that the moving parts are in good working
order, that they do not jam, and that no parts are
damaged. Make sure that all parts are tted cor-
rectly and that all other operating conditions are
properly fullled.
Unless otherwise stated in the operating instruc-
tions, damaged safety devices and parts have to
be repaired or replaced by an authorized service
center.
Have damaged switches replaced by a customer
service workshop.
This electric tool complies with the pertinent safety
regulations. Repairs are to be carried out only by
a qualied electrician using original replacement
parts or the user may suffer an accident.
If necessary, wear suitable personal protection
equipment. This could consist of:
- Ear-muffs to prevent the risk of damaging your
hearing
- A breathing mask to prevent the risk of inhaling
hazardous dust
The operator has to be informed about the condi-
tions with an inuence on noise development.
Faults on the machine have to be reported to the
person in charge as soon as they are discovered.
This appliance is not suitable for the collection of
dangerous dust.
This equipment is not designed to be used by peop-
le (including children) with limited physical, sensory
or mental capacities or those with no experience
and/or knowledge unless they are supervised by a
person who is responsible for their safety or they
have received instructions from such a person in
how to use the equipment safely. Children must al-
ways be supervised in order to ensure that they do
not play with the equipment.
Remaining hazards
The machine has been built using modem techno-
logy in accordance with recognized safety rules.
Some remaining hazards, however, may still exist.
Wood chips and sawdust can be health hazards.
Be sure to wear personal protective gear such as
safety goggles and a dust mask.
Dust inhalation may occur when closing and replac-
ing the dust bag.
Please note the instructions concerning proper dis-
posal in the operating manual (e.g. the use of P2
dust masks) to prevent dust inhalation.
Noise can be a health hazard. The permitted noise
level is exceeded when working. Be sure to wear
personal protective gear such as ear protection.
The use of incorrect or damaged mains cables can
lead to injuries caused by electricity.
Even when all safety measures are taken, some re-
maining hazards which are not yet evident may still
be present.
GB
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HD15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HD15 in the language / languages: All languages as an attachment in your email.

The manual is 5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info