781454
18
Zoom out
Zoom in
Previous page
1/120
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
18 / 120
Check your extension cables regularly and replace
them if damaged.
When working outdoors, use only extension cables
that are approved for outdoor use and which are
marked accordingly.
Concentrate on what you are doing. Use common
sense. Do not operate the tool if your mind is not
on your work.
Never use an electric tool with a switch that cannot
be turned on and off. Warning! The use of plug-
in tools and accessories other than those intended
may put you at risk of injury.
Always pull the plug out of the power socket before
adjusting or servicing the machine.
Give these safety regulations to all persons who
work on the machine.
Before you use the machine for the rst time, check
that the voltage marked on the rating plate is the
same as your mains voltage.
If you need to use an extension cable, make sure
its conductor cross-section is big enough for the
equipments power consumption. Minimum cross-
section: 1.5 mm2.
If you use a cable reel, the complete cable has to
be pulled off the reel. Check the power cable. Ne-
ver use a faulty or damaged power cable.
Do not use the cable to pull the plug out of the so-
cket.
Protect the cable from heat, oil and sharp edges.
Do not leave the machine in the rain and never use
it in damp or wet conditions.
Provide good lighting.
Do not saw near ammable liquids or gases.
Non-slip shoes are recommended when working
outdoors. Wear a hair net if you have long hair.
Avoid abnormal working postures.
Operators have to be at least 18 years of age. Trai-
nees of at least 16 years of age are allowed to use
the machine under supervision.
Keep children away from the machine when it is
connected to the power supply.
Keep your workplace clean of wood scrap and any
unnecessary objects. An untidy work area invites
accidents.
Do not allow other persons, especially children, to
touch the tool or cable. Keep them out of your work
area.
Persons working on the machine should not be dis-
tracted.
Carry out conversions, adjustments, measure-
ments and cleaning jobs only when the motor is
switched off. - Pull out the power plug!
Before switching on, make sure that all keys and
wrenches have been removed from the tool.
Switch off the motor and pull out the power plug
before you leave the workplace.
Ret all guards and safety devices immediately af-
ter you have completed any repairs or maintenance
work.
Be sure to observe the safety information and ope-
rating and maintenance instructions issued by the
manufacturer, as well as the dimensions listed in
the Technical Data.
It is imperative to observe the accident prevention
regulations in force in your area as well as all other
generally recognized rules of safety.
Regularly check that the housing is well sealed and
regularly inspect the lter and saw dust sackseals.
Do not allow foreign objects such as screws, nails,
plastic or wood chips to enter the cleaning nozzle.
The machine must only be used with original parts
and orginal accessories supplies by the manufac-
turer.
The Exhaust System is constructed exclusively for
exhaust-vacuuming wood chips and saw dust and
may only be used in connection with wood process-
ing machines.
When vacuuming shop oors, wood or metal pieces
may not be vacuumed.
Any other use exceeds authorization. The manufac-
turer is not responsible for any damagesresulting
from unauthorized use; risk is the sole responsibility
of the operator.
The safety, work and maintenance instructions of
the manufacturer as well as the technical data given
in the calibrations and dimensions must be adhered
to.
Relevant accident prevention regulations and other,
generally recognized safety-technical rules must
also be adhered to.
The machine may only be used, maintained, and
operated by persons familiar with and instructed in
its operating and procedures. Arbitrary alterations
to the machine release the manufacturer from all
responsibiliy for any resulting damages.
The machine may only be used with original acces-
sories made by the manufacturer.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
equipment is used in commercial, trade or industrial
businesses or for equivalent purposes.
5. Safety information
Attention! The following basic safety measures
must be observed when using electric tools for
protection against electric shock, and the risk of
injury and re. Read all these notices before using
the electric tool and keep the safety instructions for
later reference.
Safety information
Warning: When using electric tools it is imperative
to take the following basic safety precautions in or-
der to reduce the risk of electric shock, injury and
re.
Take due note of all this information before and
while working with the machine.
Do not lose these safety regulations.
Guard against electric shock Avoid body contact
with earthed parts.
When equipment is not being used it should be kept
in a dry, closed place out of childrens reach.
Keep mounted attachments sharp and clean to
enable you to work well and safely.
Check the power cable regularly and have it repla-
ced by an authorized specialist at the rst sign of
any damage.
GB
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HD15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HD15 in the language / languages: All languages as an attachment in your email.

The manual is 5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info