Manual Scheppach HC08 (page 17 of 96) (English, German, Danish, French, Italian, Swedish)

758664

Zoom out

Zoom in

1/96

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

17 І 96

maximum level. This is marked with a red dot on the oil

level window (10) (Fig. 8 pos. 10.1). Do not exceed the

maximum lling quantity. Overlling the equipment may

result in damage. Reinsert the oil sealing plug (9) into

the oil ller opening (9.1).

10.6 Cleaning the intake lter (Fig. 4, 6)

The intake lter prevents dust and dirt being drawn in.

It is essential to clean this lter after at least every 300

hours in service. A clogged intake lter will decrease

the compressor’s performance dramatically. Open the

thumb screw (A) to the remove the intake lter.

Then pull off the  lter cover (C). Now you can remove

the air lter (E) and the lter housing (D). Carefully tap

out the air lter, lter cover and lter housing. Then blow

out these parts with compressed air (approx. 3 bar) and

reinstall in reverse order.

10.7 Storage

m Important!

Pull out the mains plug and ventilate the equip-

ment and all connected pneumatic tools. Switch

off the compressor and make sure that it is secured

in such a way that it cannot be started up again by

any unauthorized person.

m Important!

Store the compressor only in a dry location which

is not accessible to unauthorized persons. Always

store upright, never tilted!

10.8 Releasing excess pressure

Release the excess pressure by switching off the com-

pressor and using the compressed air which is still left

in the pressure vessel, e.g. with a compressed air tool

running in idle mode or with a blow-out pistol.

11. Disposal and recycling

The equipment is supplied in packaging to prevent it

from being damaged in transit. The raw materials in this

packaging can be reused or recycled. The equipment

and its accessories are made of various types of mate-

rial, such as metal and plastic. Defective components

must be disposed of as special waste. Ask your

dealer or your local council.

10.1 Cleaning

• Keep the equipment free of dirt and dust as far as

possible. Wipe the equipment with a clean cloth or

blow it down with compressed air at low pressure.

• We recommend that you clean the equipment imme-

diately after you use it.

• Clean the equipment regularly with a damp cloth and

some soft soap. Do not use cleaningagents or sol-

vents; these may be aggressive to the plastic parts

in the equipment. Ensure that no water can get into

the interior of the equipment.

• You must disconnect the hose and any spraying tools

from the compressor before cleaning. Do not clean

the compressor with water, solvents or the like.

10.2 Maintenance work on the pressure vessel/con-

densed water (Fig. 1/2)

m Important!

To ensure a long service life of the pressure vessel

(3), drain off the condensed water by opening the

drain valve (11) each time after using.

Release the vessel pressure rst (see 10.8). Open the

drain screw by turning counter-clockwise (looking at

the screw from the bottom of the compressor) so that

all the condensed water can run out of the pressure

vessel. Then close the drain screw again (turn it clock-

wise). Check the pressure vessel for signs of rust and

damage each time before using. Do not use the com-

pressor with a damaged or rusty pressure vessel. If you

discover any damage, then please contact the customer

service workshop.

10.3 Safety valve (Fig. 3/Pos. 12)

The safety valve (12) has been set for the highest per-

mitted pressure of the pressure vessel. It is prohibited

to adjust the safety valve or remove its seal. Actuate the

safety valve from time to time to ensure that it works

when required. Pull the ring with suf cient force until

you can hear the compressed air being released. Then

release the ring again.

10.4 Checking the oil level at regular intervals (Fig-

ure 8)

Place the compressor on a level and straight surface.

The oil level must be between the MAX and MIN marks

on the oil level window (10).

Oil change: we recommend SAE 15W 40 or equivalent.

The original oil  lling must be changed after 100 hours

in operation; thereafter the oil must be drained and

replaced with new oil after every 500 hours in operation.

10.5 Changing the oil (Figure 8/9)

Switch off the engine and pull the mains plug out of the

socket. After releasing any air pressure you can un-

screw the oil drain plug (10) from the compressor pump.

To prevent the oil from running out in an uncontrolled

manner, hold a small metal chute under the opening

and collect the oil in a vessel. If the oil does not drain

out completely, we recommend tilting the compressor

slightly. When the oil has drained out, re t the oil drain

plug (10).

Dispose of the old oil at a drop-off point for old oil.

To ll in the correct quantity of oil, make sure that the

compressor stands on an even surface. Fill new oil

through the oil ller opening (9.1) until it comes up to the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HC08 in the language / languages: English, German, Danish, French, Italian, Swedish as an attachment in your email.

The manual is 5,86 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HC08 Manual

Product: