Manual Scheppach FS3600 (page 17 of 80) (English, German, Dutch, French)

644541

Zoom out

Zoom in

1/80

• Contact du disque diamant dans la zone non proté-

gée.

• Éjection des pièces et morceaux de pièces.

• Éjection d’un embout de disque diamant défectueux.

• Troubles auditifs en cas de non utilisation d’une pro-

tection auditive adéquate.

• Lésions oculaires en cas de non utilisation d’une pro-

tection oculaire.

• Toute utilisation autre que celle décrite précédemment

est considérée comme non conforme. Le fabricant

n’est pas responsable des dommages qui en dé-

coulent ; l’utilisateur en est le seul responsable.

Avant la mise en service

Remplacez des disques diamant ssurés.

• Familiarisez-vous avec votre machine. Prenez

connaissance de votre application et de ses limites,

mais aussi des dangers potentiels spéciques.

• Vériez avec soin que la machine n’est pas endom-

magée pour assurer qu’elle puisse fournir le rende-

ment prévu. En cas de doutes, remplacez la pièce

concernée.

• Assurez-vous que l’interrupteur soit sur ARRÊT (AUS)

avant de brancher le connecteur dans la prise.

• Assurez-vous que la machine ait bien été nettoyée

et lubriée.

• Avant la mise en service, vériez que certaines pièces

de la machine ne sont pas endommagées et vériez

sicelles-ci fonctionnent convenablement et rem-

plissent la fonction prévue.

• Vériez l’alignement de toutes les pièces mobiles, de

toutes les pièces brisées ou des attaches, et toutes

les conditions pouvant affecter le bon fonctionnement.

Toute pièce endommagée doit immédiatement être

réparée ou remplacée par un spécialiste.

• Ne pas utiliser la machine si un interrupteur ne fonc-

tionne pas correctement.

Fonctionnement

• Placez la machine sur une surface plane et stable.

• Vériez que la tension sur la plaque signalétique cor-

respond à la tension présente avant de brancher le

connecteur dans la prise de courant.

• Le disque doit pouvoir fonctionner de manière libre

avant la mise en marche.

Attention: Le disque doit toujours être refroidi avec de

l’eau.

Attention: Le disque fonctionne de manière décalée.

• Ne pas freiner le disque par pression latérale.

• Le carter moteur peut être chaud lors de l’utilisation

normale.

• Ne pas forcer la machine ou les accessoires pour ef-

fectuer les travaux d’une plus grande machine indus-

trielle. Elle fonctionne mieux et de manière plus sûre

• Ejection of a faulty diamond attachment in the cut-

ting disc.

• Hearing damage due to non-use of the required hear-

ing protection.

• Injuries to the eyes due to non-use of eye protection

Any use beyond the one specied will be treated as im-

proper. The manufacturer will not be liable for damages

resulting from such improper use; the risk will be borne

by the user alone.

Before start-up

Replace cracked diamond cutting discs.

• Get to know your machine. Familiarize yourself with

its use and its restrictions, but also with the specic

potential risks.

• Check the machine carefully for damages to ensure

that it is able to achieve the intended output. In case

of doubt, please replace the concerned component.

• Ensure that the switch is on Off, before inserting the

power plug into the mains socket.

• Ensure that the machine is cleaned and lubricated

properly.

• Before start-up, check the machine for damaged parts

and nd out whether these parts are working properly

and performing their dened function.

• Check the alignment of all moving parts, all broken

or fastening parts, and all other conditions that can

affect smooth operation. Each damaged part should

be repaired or replaced by a technician immediately.

• Do not use the machine if a switch cannot be activat-

ed/deactivated correctly.

Operation

• Install the machine on an even, slide-proof oor.

• Check that the voltage on the nameplate matches the

existing voltage; connect the power plug to the mains

power supply only thereafter

• The cutting disc should be free to run before the ma-

chine is switched on.

Caution: Cutting disc must always be cooled with water.

Caution: Cutting disc runs with a time lag.

Do not break the cutting disc by applying pressure at the

sides.

• Under normal use conditions, the motor casing can

become hot.

• Do not use force on the machine or on an accessory

to achieve the performance of a bigger Industrial ma-

chine. It does a better job at the output for which it is

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach FS3600 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach FS3600 Manual

Product: