782263
32
Zoom out
Zoom in
Previous page
1/42
Next page
32 english
Fault Possible Cause Remedy
saw blade detachs after motor is switched off fastening nut too slack tightenM20lefthandedfasteningnut
motor fails to start a)mainsfuseoutage a)checkmainsfuse
b)faultyextensioncable b)
refertosectiononelectricalconnection,inthe
operating instructions
c)faultyconnectionstomotororswitch,brake
fails to release
c)shouldbecheckedbyaqualifiedelectrician
d)faultymotororswitch d)
seesectiononelectricalconnection,inthe
operating instructions
e)sawbladeprotectivecoveropen e)closesawbladeprotectivecover
incorrect motor rotational direction a)faultycapacitor a)shouldbereplacedbyaqualifiedelectrician
b)incorrectconnection b)wallsocketpolarityshouldbechangedbya
qualified electrician
nomotoroutput,motorswitchesoffautomati-
cally
a)overloadcausedbydullsawblade a)installsharpenedsawblade
b)thermalprotectionactivates b)canbeswitchedonagainaftercooling
period
burn marks where cut is made
on cross section
a)dullsawblade a)installsharpenedsawblade
b)incorrectsawblade b)installsawbladeforlengthwisecuts
c)fencenotparalleltosawblade c)replacefence
d)slidingtablecarriagenotparalleltosaw
blade
d)alignslidingtablecarriagetosawblade
reduced saw performance at full motor speed loose belt tightenbelt,refertomaintenancesection
workpiece jams between sawblade and fence fence does not run parallel to saw blade check fence alignment
sliding table carriage does not move a)lockhasnotbeenreleased a)releaselock
b)guideunitisdirty b)cleanguideunit
markedasH07RN.
Regulationsrequirethatthetypedesignationbeprintedon
the connection cable.
AC Motor
• Therequiredsupplyvoltageis230Volt50Hz.
• Extensioncablesupto25minlengthmusthaveacross
sectionof1.5mm2;extensioncableswhichexceed25
m in length must have a cross section of 2.5 mm2.
• Themainsconnectionhasa16Atimedelayfuse.
Three-Phase Current Motor
The400V/50HzelectricmotorisdesignedfortheS6/40%
operating mode.
• Therequiredsupplyvoltageis400Volt50Hz.
• The mains connection and extension cable must be
equippedwith5wires=3P+N+PE.
• Extensioncablesmusthavea crosssectionofnoless
than 1.5 mm2.
• Themainsconnectionisfusedtoamaximumof16A.
• Checkthe rotational directionwhen connecting tothe
powersupplyorchanginglocation:itmaybenecessary
tochangethepolarity(wallsocket).
If you have questions always provide the following information:
• motormanufacturer
• typeofcurrentusedbymotor
• datalistedonthemachinetypeplate
If you return the motor always send the complete drive unit
including switch.
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Forsa 4.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Forsa 4.0 in the language / languages: English, German as an attachment in your email.

The manual is 7.02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info