782263
31
Zoom out
Zoom in
Previous page
1/42
Next page
english 31
Maintenance
Switch off the motor and disconnect the power supply plug
before doing any maintence and cleaning work. Follow the
following maintenance procedures for your panel sizing circular
saw.
• Checkbelttensionafterapprox.20operatinghour and
tighten if necessary. To do this open the right side cover.
Set required belt tension by adjusting the fastening nuts
on the motor equally.
• Spray the roller chain and moving parts (vertical and
swiveladjustmentunits)occasionallywithdrylubricating
spray. Open the right side cover.
• Checkthe sliding table carriage guide unit fordirt and
clean if required.
• Alwayskeepthetablesurfacefreeofresin.
• If a dust extractor is not being used the saw blade
protective cover should be cleaned occassionally of any
wood residue and sawdust. This is important for ensuring
troublefree ejection of sawdust. If the machine is used
without a dust extractor sawdust accumulation could
reduce the vertical and angle adjustment range.
• Cleantheslidingtablecarriageguideatregularintervals.
All safety equipment and protective devices must be reattached
as soon as repair and maintenance work has been completed.
• Toensuretroublefreeejectionofsawdustthesawblade
protective cover should be cleaned of any wood residue.
• T h e vertical and angle adjustment range could
b e reduced if sawdust is allowed to accumulate.
Open the protective cover and clean the adjustment
area.
Electrical Connection
The built in electric motor is wired ready for operation. The
connection conforms with the applicable VDE and DIN
regulations.
The mains connection on site and the extension cable used
should also comply with these regulations.
Motor Brake Device
Yourpanelsizingcircularsawisequippedwithanautomatic
shutdown brake. The brake starts to take effect after the
driving motor switches off.
The saw blade must stop max.10 sec after switching off. Check
daily!
Do not operate the machine after a longer braking time.
Important Information
The 230 V / 50 Hz and 400 V / 50 Hz electric motors are
designed for S6 40 % operating mode.
If the motor starts to overload it switches off automatically. The
motor can reactivated after a cooling period (exact interval
differs).
Faulty Electric Connection Cables
Electric connection cables are frequently subjected to
insulation damage.
Insulation damage results from:
• Pinchpointswhereconnectioncablesareroutedthrough
windows or door cracks.
• Kinksduetoimproperfasteningorroutingofconnection
cables.
• Cutscausedbyrunningoverconnectioncords.
• Insulationdamagecausedbypullingthecableoutofthe
wall socket.
• Cracksduetoaging.
Faulty or damaged electric connection cables are hazardous
and should not be used under any circumstances as fatal
injury could result.
Check electric connection cables regularly for damage.
Beforeyouchecktheconnectioncable,makesurethatit
has been completely disconnected from the power supply.
Electricconnectioncablesmustconformtotheapplicable
VDE and DIN regulations. Use only connection cables
2-3mm
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Forsa 4.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Forsa 4.0 in the language / languages: English, German as an attachment in your email.

The manual is 7.02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info