782263
20
Zoom out
Zoom in
Previous page
1/42
Next page
20 english
- refer to the numbers imprinted on the riving knife. The
riving knife should never be thinner than the body of the
saw blade or thicker than the cutting joint width.
• Lowerthesuctionhoodontotheworkpieceduringevery
working cycle.
• Thehoodmustbepositionedhorizontallyabovethesaw
blade during every working cycle.
• Always use the pushstick when cutting narrow
workpieces(lessthan120mminwidth)lengthwise.
• Switch off the machine during troubleshooting or to
remove jammed pieces of wood. Disconnect power
supply plug!
• Wearclosettinggarments.Donotwearjewelry,ringsor
wrist-watches.
• Check direction of motor and tool rotation (refer to
"ElectricalConnection").
• Machine safety equipment should not be detached or
disabled under any circumstances.
• Themotormustbeswitchedoffduringanyconversion,
adjustment, measurement and cleaning work to the
machine. Disconnect the power supply plug and wait
until the rotating saw has come to a complete stop.
• Switch off the machine before remedying faults.
Disconnect power supply plug!
• Themachinemustbeconnectedtoadustextractorat
all times during use. Follow the instructions for proper
use.
• All safety equipment and hoods must be installed to
operate the machine.
• Priortoinitialoperationthemachinemustbeconnected
toadustextractorbymeansofaexible,nonammable
suction hose.
• Thedustextractorshouldswitchonautomaticallywhen
the panel sizing circular saw is activated.
• Switch off the motor when leaving the work area.
Disconnect power supply plug!
• Alwaysdisconnectthemachinefromallexternalpower
sources before moving it, no matter how slightly!
Reconnect the machine to the power supply before
restarting the machine!
• Installation, repair and maintenance work on the
electrical equipment should be done by qualified
electricians only.
• All safety equipment and protective devices must be
reattached as soon as repair and maintenance work has
been completed.
Proper Use
• ThismachinecomplieswiththeapplicableECmachine
guideline.
• This machine has a work area located in front of the
machine to the left or right of the saw blade.
• Topreventaccidentstheworkareaandtheareaaround
the machine must be clear of any foreign objects which
could interfere with machine operation.
• Workpiecesshouldnotcontainanyforeignobjectssuch
as nails or screws.
• Priortoinitialoperationthemachinemustbeconnected
toadustextractorbymeansofaexible,nonammable
suction hose.
• Foruseinclosedspacesthemachinemustbeconnected
to a dust extractor. Use a ha 3200 or ha 2600 dust
extractor to extract wood shavings or sawdust. The flow
rateatthesuctionconnectionpieceshouldbe20m/s.
Partialvacuum1200Pa.
• Theautomaticswitchondeviceisavailableasaspecial
accessory.
TypeALV2 Art.No.79104010 230V/50
Hz
TypeALV10 Art.No.79104020 400V/50
Hz
When the machine is switched on the dust extractor
switches on automatically after a 2 - 3 second time
delay. This prevents overstress to the house fuse.
After the machine has been switched off the dust
extractor continues to run for 3  4 seconds before
switching off automatically.
This ensures that residual dust is extracted in accordance
with the hazardous materials ordinance. This conserves
electricity and reduces noise. The dust extractor runs
only when the machine is in operation.
Forindustrialworkusetherg4000dustextractor.
Do not switch off or remove dust extractors when the
machine is in operation.
• The panel sizing circular saw is designed for use in
processingwoodorwoodlikematerialsonly.Usegenuine
parts and accessories only. Select the correct saw blade
accordingtotypeofcutandtypeofwood(solidwood,
plywoodorparticleboard)inaccordancewithEN847
1.Refertothespecialaccessorieslist.
• Themanufacturershallnotbeheldliableforimproper
use!!
Additional Hazards
This machine is designed in accordance with state of the
art technology and accepted standards of technical safety.
In spite of this certain additional hazards may occur during
operation of this machine.
• Riskofinjurytongersandhandsfromrotatingsawor
workpiece if saw or workpiece is routed improperly.
• Riskofinjuryfromrotatingsawresultingfromimproper
mounting or guide control or from operation without end
stop.
• Healthrisksduetoexcessivenoise.Permissablenoise
levels are exceeded during operation of the machine.
Alwayswearearprotection.
• Riskofinjuriesfromdefectivesawblade.Checkblade
condition regularly.
• Electrical hazards if improper connection cables are
used.
• In spite of all safety precautions instituted additional
unforseeable hazards may occur.
• To minimize the risk of additional hazards follow all
"safetyinstructions",instructionsfor"properuse",and
operating instructions carefully.
Special accessories
Art.No.
Workpieceholder 54720702
Crosstablewithtelescopicarm 54720704
Crosstablewithtelescopicarm 54720705
SUVAexhaustdevice 54720707
AutomaticswitchondeviceALV2 79104010
AutomaticswitchondeviceALV10 79104020
Table extension 7901700701
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Forsa 4.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Forsa 4.0 in the language / languages: English, German as an attachment in your email.

The manual is 7.02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info