Manual Scheppach Forsa 3.0 (page 25 of 48) (English, German)

782262

Zoom out

Zoom in

1/48

a table extension. The second person must not stand at any

place other than at the discharge end of the table extension.

• Secure larger workpieces against tipping. (e.g. for example

with a dolly)

• All protective devices and covers must be installed before any

work is carried out on the machine.

• With all work processes, connect the machine to a

scheppach suction system with a exible, low-ammability

suction line. Observe the proper use of the machine with this.

The suction system must switch on autonomously with the

switching on of the panel sizing saw.

• Observe the turning direction of the motor and the tool - see

„Electrical connection“.

• Ensure that you use the push rod with the longitudinal cutting

of narrow workpieces (smaller than 120 mm)

• Lower the protective hood onto the workpiece with every

working operation.

• The protective hood must be horizontal above the saw blade

with each working operation.

• Renew the table insert if the sawing gap has become worn.

Remove the mains plug!

Tools

• Only insert tools that comply with the European standard DIN

EN 847-1.

• Use only saw blades that are well sharpened, free of cracks

and not deformed.

• Do not use circular saw blades made from high performance

steel.

Protective clothing

• Wear tight-tting clothing. Take off jewellery, rings and wrist-

watches.

• Wear hearing protection and protective goggles when working.

• Wear gloves when replacing the saw blade.

• Do not wear gloves during sawing operations

Storage and operating conditions

• Operating conditions: Do not use the machine outside but only

in enclosed rooms.

• Storage conditions: Air humidity must be at least 90% and

must be non-condensing.

Transport

• Disconnect the machine from external power supplies, even

with minor changes in location! Re-connect the machine pro-

perly with the mains power before re-commissioning.

Maintenance and repairs

• Have malfunctions that could inuence safety dealt with imme-

diately.

• Only carry out modications, adjustments, measurements and

cleaning work with the motor switched off. Pull out the mains

plug and wait until the rotating tool has come to a standstill.

• Reinstall all protection and safety equipment immediately after

nishing repair or maintenance work.

• Have installation, repair and maintenance work on the electri-

cal system carried out exclusively by electricians.

• Switch the machine off to rectify faults or to remove jammed

pieces of wood. Wait until the saw blade has come to a stand-

still. Remove the mains plug!

Proper use m

General

• The machine complies with the applicable EC machinery

directive.

• The scheppach panel sizing saw is dened as a machine per

EN 1870/-1.

• The machine has a workstation which is located in front of the

machine to the left or right of the saw blade.

• The working area and surroundings of the machine must

be kept free of disruptive foreign bodies in order to prevent

accidents

• In principle, the workpieces to be processed must be free of

foreign bodies such as nails or screws.

• The manufacturer assumes no liability for damages arising

from inappropriate use!

• The machine is intended to be used in commercial applica-

tions.

• The scheppach panel sizing saw is designed exclusively for

the processing of wood and wood-like materials.

Tool

• Only original scheppach tools and accessories may be used.

Use the appropriate saw blade depending on the type of

cutting and the type of wood (solid wood, laminated wood or

chipboard) per EN 847-1. Observe the scheppach „Tools and

special accessories“ .

Suction system

• Before start-up the machine must be connected to a suction

system with a exible, low-ammability suction line. For ext-

racting the wood chippings or sawdust a suitable scheppach

suction system should be employed. The ow speed at the

suction nozzle must be 20 m/s. Negative pressure 1250 Pa.

• The scheppach auto switch-on device is available as a

special accessory.

• Type ALV2 item no. 79104010 230V 150 Hz

• Type ALV10 item no. 79104020 400V 150 Hz When switching

on the tool the suction system will start up automatically

after a 2-3 second start-up delay. This prevents overloading

the workshop fuse or circuit breaker. After switching off the

tool the suction system continues to run for 3-4 seconds

afterwards and then switches off automatically. The residual

dust is thus extracted, as required by the hazardous materi-

al ordinance. This saves power and reduces the noise. The

suction system only runs whilst the tool is being operated. For

work in commercial areas the scheppach suction system

woova 7.0 must be employed for the extraction of the dust. Do

not switch off or remove the suction system whilst the tool is

running.

Residual risks m

The machine has been built according to the state-of-the-art

and the recognised technical safety requirements. However,

individual residual risks can arise during operation.

• Risk of injury for ngers and hands due to the rotating cutting

tool with improper guiding of the workpiece.

• Injuries due to the workpiece being ejected at high speed with

improper holding or guiding, such as working without the stop.

• Risk to health due to noise. The permissible noise level is

exceeded during operations. It is essential that personal pro-

tective equipment, such as hearing protection, is worn.

• Injuries due to defective saw blade. Check the integrity of the

saw blade regularly.

DGB

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Forsa 3.0 in the language / languages: English, German as an attachment in your email.

The manual is 5.68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach Forsa 3.0 Manual

Product: