Manual Scheppach DS920 (page 18 of 68) (English, German, Dutch, French, Finnish)

781636

Zoom out

Zoom in

1/68

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

18 І 68

Before start-up

unpacking

1. Open the packaging and carefully takeout the power

tool.

2. Remave the packaging material as weil as the pa-

ckaging I transport Iacks (if any).

3. Check the scope of delivery for completeness and

check the power tool and the accessory parts for

transport damage.

Note: Do not start the power tool if you notice that

parts are missing or damaged. Contact the retailer

where you purchased this power tool.

4. Store the packaging until the end of the warranty pe-

riod, if possible. Piease dispose ofthe packaging in

accordance with environmental regulations and take

it to a recycling depot.

WARNING!

Neither power tools nor packaging materials are

toys! Children must not play with plastic bags,

foils and small parts! Danger of swallowing and

suffocation!

Installation

- Fold the front and back parttagether (Fig.2). And

then tighten the screw nut. (Fig.3).

- The Iongest length installation Insert the additional

handle to the end of the machine. And then turn the

screw nut on the end ofthe machine for tightening.

(Fig.4)

Sandpaper

Selection

1. The grain size of the sandpaper is specied on its

rear side. The smaller the specied number, the

coarser the graining.

2. Use sandpaper with coarse grain for rough grinding,

and sandpaper with ne grain for nishing. We re-

cornrnend sandpapers with aluminium oxide, silicon

carbide or other synthetic abrasives.

3. lf you can chose between sandpapers with different

graining, you should start with coarsegraining sand-

paper and complete the grinding process with the

nest possible graining. Thus you will get good and

smooth grinding results.

How to apply and replace sandpaper

Apply the sandpaper (13) to the grinding plate (9)

using the Velcro strip mechanism.

1. Align the sandpaper (13) with the grinding plate (9)

and press it on evenly.

2. PuII the sandpaper (13) off the grinding plate (9) and

replace it with a new one I another one (Fig.5).

Dust extraction

WARNING! Harmfull noxious gases may be generated

when e.g. lead-containing paint is processed. These

gases entail a risk for the operator and the persons in

the vicinity!

Therefore only use the power tool in combination with

a dust extraction unit, and protect yourself and other

persons in the working area with additional suitable

personal protective equipment!

When working with this power tool, a Iot of dust is ge-

nerated. The dust extraction unit is very useful if you

want to keep your workplace clean. lt is possible to

combine the extraction system or a vacuum cleaner

with the extraction hose (11) which is connected to the

adapter for dust extraction.

1. Align the nose at the hoseend with the extraction ho-

se adapter (12) (Fig.3), insert the end and secure it

by turning in a clockwise rotation (Fig.7).

Additional safety notes

a) Connect a vacuum cleaner to the supplied adapter

before starting your operations.

b) Attention! Keep away grinding dust from open Iire.

Dust may be explosive.

c) Always wear goggles and a dust mask when grin-

ding, in particular du ring overhead work and when

processing critical materials! When grinding certain

materials (e .g.lead paint, certain types of wood and

metaI) harmful or noxious dust may be generated.

Touching or breathing in such dust may imply risks

for the operator or people in the vicinity.

Notes regarding vibration and noise emissions

Reduce noise emissions and vibrations to a minimum!

1. Only use power tools which are free of defects.

2. Maintain and clean the power tool on a regular ba-

sis.

3. Adjust your way of working to the power tool.

4. Do not overload your power tool.

5.Have your power tool inspected, if necessary.

6. Switch off the power tool when it is not in use.

Remaining risks

Even if you use this power tool in compliance with

the regulations, there arestill remaining risks. The fol-

lowing risks may occur due to the type and design of

the power tool:

a) Damage caused to your health resulting from hand/

arm vibrations if the power tool is used over a Ionger

period of time or if it is not properly used and main-

tained.

b) lnjury and damage to property caused by ying off

insertion tools which are unexpectedly expelled from

the power tool due to sudden damage, wear or in-

correct insertion.

c) Burns and cuts if the insertion tools are touched di-

rectly after use and/or with your bare hands.

Warning! This electric tool generates an electromag-

netic eld du ring operation which may impair active or

passive medical implants under certain circumstances.

ln order to reduce the risk of severe or Iethal injury, we

recommend that persons with medical implants consult

their doctor and the manufacturer of the medical im-

plant before using the power tool.

Tool description and scope of delivery

Tool description (Fig.1)

The tool description refers to the illustration at the be-

ginning of this instruction manual.

1. Handle surface

2. Main handle

3. On/off switch

4. Adapter with connecting nut

5 Powercord

6. Adjustment wheel for speed pre-selection

7. Ventilation opening

8. Flexible grinding head

9. Grinding plate

10. Brush edge

11. Extraction hose

12. Hoseadapter

13. Abrasive sheet

14. LED-Light

Scope of delivery (Fig.1)

1 drywall sander

1 extraction hose (1 1)

2 hose adaptor (1 2)

6 abrasive sheets (1 3) (different grain sizes)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DS920 in the language / languages: English, German, Dutch, French, Finnish as an attachment in your email.

The manual is 2.85 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach DS920 Manual

Product: