782104
10
Zoom out
Zoom in
Previous page
1/60
Next page
english 9
Manufacturer
Scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
We wish you much pleasure and success with your new
scheppach machine.
Note
In accordance with valid product liability laws, the manu-
facturer of this device shall not be responsible for damage
to and from this device which results from:
• Improper care.
• Noncompliance with the Operating Instructions.
• Repairs made by unauthorized persons.
• The installation and use of any parts which are not
original scheppach replacement parts.
• Improper use and application.
• Failure the electrical system as a result of noncompli-
ance with the legal and applicable electrical directives
and VDE regulations 0100, DIN 57113 / VDE 0113.
We recommend
that you read through the entire operating instructions be-
fore putting into operation.
These operating instructions are to assist you in getting to
know your machine and utilize its proper applications.
The operating instructions contain important notes on how
you work with the machine safely, expertly, and economi-
cally, and how you can avoid hazards, save repair costs,
reduce downtime and increase the reliability and service
life of the machine.
In addition to the safety requirements contained in these
operating instructions, you must be careful to observe your
country’s applicable regulations.
The operating instructions must always be near the ma-
chine. Put them in a plastic folder to protect them from
dirt and humidity. They must be read by every operator
before beginning work and observed conscientiously. Only
persons who have been trained in the use of the machine
and have been informed of the various dangers may work
with the machine. The required minimum age must be ob-
served.
In addition to the safety requirements contained in these
operating instructions and your country’s applicable reg-
ulations, you should observe the generally recognized
technical rules concerning the operation of woodworking
machines.
General notes
• After unpacking, check all parts for any transport dam-
age. Inform the supplier immediately of any faults.
• Later complaints cannot be considered.
• Make sure the delivery is complete.
• Before putting into operation, familiarize yourself with
the machine by carefully reading these instructions.
• Use only original scheppach accessories, wearing or
replacement parts. You can find replacement parts at
your scheppach dealer.
• When ordering, include our item number and the type
and year of construction of the machine.
dms 1200 vario
Included with delivery
Wood turner lathe
Tool holder
Driver
Live tailstock center
Tensioning spindle
Face plate
Mid. top
Assembly tools
Operating instructions
Technical data
Dimensions
L x B x H mm 2060 x 500 x 1200
Bed height mm 920
Headstock thread M33
Height of centers above
bed mm 230
Width between centers
mm 1200
Diameter above bed
mm 460
Diameter between
centers mm 350
Length of tool holder
mm 355
Face plate ø mm 152
Weight kg 190,0
Wood turning spindle with dust-proof precision grooved ball bearing
Revolutions 1/min 01200
12003200
Tailstock
Tailstock cone MK2
Tailstock drill hole
(hollow spindle) ø mm 9
Tailstock sleeve
adjustment mm 55
Drive
Electric Motor 230–240V/50 Hz
Input P1 kW 2,5
Output P2 kW 2,1
Revolutions 1/min 1400
Motor protection yes
Undervoltage release yes
Switch - plug
combination Netzstecker
Operating mode S6 40%
Subject to technical modifications!
Noise parameters
The noise emission values at the work place, determined
according to EN 23746 (acoustic power levels) and EN
31202 (acoustic pressure levels) with a correction factor
k3 calculated according to appendix A.2 of EN 31204,
based on operating conditions listed in ISO 7904, appen-
dix A, are:
Acoustic power level in dB
Idling LWA = 81.9 dB(A)
Operating LWA = 84.5 dB(A)
Acoustic pressure level in dB
Idling LpAeq = 72.4 dB(A)
Operating LpAeq = 76.2 dB(A)
A measuring uncertainty coefficient (K = 4 dB) applies to the
emission values listed above.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach DMS 1200 Vario at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DMS 1200 Vario in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 4.47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info