782104
9
Zoom out
Zoom in
Previous page
1/60
Next page
8 deutsch
EG-Konformitätserklärung
Hiermit erklären wir, die Scheppach Fabrikation von
Holzbearbeitungsmaschinen GmbH, Günzburger Str. 69,
D-89335 Ichenhausen, dass die nachfolgend bezeich nete
Maschine aufgrund ihrer Konstruktion und Bauart sowie
in der von uns in Verkehr gebrachten Ausführung den
einschlägige Bestimmungen nachstehender EG-Richtlinien
entspricht.
Bei einer Änderung an der Maschine verliert diese Erklärung
ihre Gültigkeit.
Bezeichnung der Maschine:
Drechselmaschine
Maschinentyp:
dms 1200 Vario
Einschlägige EG-Richtlinien:
EG-Maschinenrichtlinie 98/37/EG (bis 28.12.2009),
EG-Maschinenrichtlinie 2006/42/EG (ab 29.12.2009),
EG-Niederspannungsrichtlinie 2006/95/EWG,
EG-EMV Richtlinie 2004/108/EWG.
Angewandte harmonisierte europäische Normen:
EN 292-1, EN 292-2, EN 294, EN 55014, EN 50082-1, EN
60555-2, EN 60 204-1
Gemeldete Stelle:
TÜV Rheinland, Product Safety GmbH, 51101 Köln
Eingeschaltet zu:
EG-Baumusterbescheinigung 9859 10402
Ort, Datum:
Ichenhausen, 08.06.2009
Unterschrift:
i.V. Wolfgang Windrich
Störungsabhilfe
Störung Mögliche Ursache Abhilfe
Motor läuft nicht an a) Kein Strom
b) Schalter, Kondensator
c) Elektrische Verlängerungsleitung defekt
a) Netzsicherung überprüfen
b) Elektro- Fachkraft überprüfen
c) Netzstecker ziehen, überprüfen, bei
Bedarf austauschen
Bohrungen werden größer
als der Bohrer
Spindelstock und Reitstock sind nicht parallel Spindelstock nach Reitstockspitze einrichten.
Hierzu Mitnehmer in die Drechselspindel
einsetzen und den Reitstock mit Spitze bis auf
ca. 1 mm Abstand anstellen.
Das Werkstück flattert
beim Arbeiten
a) Werkstück lockert sich beim Arbeiten
b) Zentrierung nicht mittig
c) Zu hohe Drehzahl
a) Arbeithinweise in Bedienungsanweisung
beachten
b) Arbeitshinweise in Bedienungsanweisung
beachten
c) Niedrigere Drehzahl wählen
Werkzeugauflage oder
Reitstock kann nicht
geklemmt werden
Einstellung der Exzenterklemmung Sechskantmutter an der Unterseite ca. ½
Umdrehung mit Steckschlüssel nachdrehen
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach DMS 1200 Vario at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DMS 1200 Vario in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 4.47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info