Manual Scheppach DM-ABS1200E - Dineiger (page 16 of 28) (English, German)

782148

Zoom out

Zoom in

1/28

16 / 28

• Check the power cable regularly and have it repla-

ced by an authorized specialist at the rst sign of

any damage.

• Check your extension cables regularly and replace

them if damaged.

• When working outdoors, use only extension cables

that are approved for outdoor use and which are

marked accordingly.

• Concentrate on what you are doing. Use common

sense. Do not operate the tool if your mind is not

on your work.

• Never use an electric tool with a switch that cannot

be turned on and off. Warning! The use of plug-

in tools and accessories other than those intended

may put you at risk of injury.

• Always pull the plug out of the power socket before

adjusting or servicing the machine.

• Give these safety regulations to all persons who

work on the machine.

• Before you use the machine for the rst time, check

that the voltage marked on the rating plate is the

same as your mains voltage.

• If you need to use an extension cable, make sure

its conductor cross-section is big enough for the

equipments power consumption. Minimum cross-

section: 1.5 mm2.

• If you use a cable reel, the complete cable has to

be pulled off the reel. Check the power cable. Ne-

ver use a faulty or damaged power cable.

• Do not use the cable to pull the plug out of the so-

cket.

• Protect the cable from heat, oil and sharp edges.

• Do not leave the machine in the rain and never use

it in damp or wet conditions.

• Provide good lighting.

• Do not saw near ammable liquids or gases.

• Non-slip shoes are recommended when working

outdoors. Wear a hair net if you have long hair.

• Avoid abnormal working postures.

• Operators have to be at least 18 years of age. Trai-

nees of at least 16 years of age are allowed to use

the machine under supervision.

• Keep children away from the machine when it is

connected to the power supply.

• Keep your workplace clean of wood scrap and any

unnecessary objects. An untidy work area invites

accidents.

• Do not allow other persons, especially children, to

touch the tool or cable. Keep them out of your work

area.

• Persons working on the machine should not be dis-

tracted.

• Carry out conversions, adjustments, measure-

ments and cleaning jobs only when the motor is

switched off. - Pull out the power plug!

• Before switching on, make sure that all keys and wren-

ches have been removed from the tool.

• Switch off the motor and pull out the power plug before

you leave the workplace.

• Ret all guards and safety devices immediately after

you have completed any repairs or maintenance work.

ned only for removing saw dust (nor for normal dust).

• Regularly inspect the lter for damage.

• Replace damaged lters!

• Regularly check that the housing is well sealed and

regularly inspect the lter and saw dust sackseals.

• Do not allow foreign objects such as screws, nails,

plastic or wood chips to enter the cleaning nozzle.

• The machine must only be used with original parts

and orginal accessories supplies by the manufac-

turer.

• The Exhaust System is constructed exclusively for

exhaust-vacuuming wood chips and saw dust and

may only be used in connection with wood proces-

sing machines.

• When vacuuming shop oors, wood or metal pie-

ces may not be vacuumed.

• Any other use exceeds authorization. The manu-

facturer is not responsible for any damagesresul-

ting from unauthorized use; risk is the sole respon-

sibility of the operator.

• The safety, work and maintenance instructions

of the manufacturer as well as the technical data

given in the calibrations and dimensions must be

adhered to.

• Relevant accident prevention regulations and

other, generally recognized safety-technical rules

must also be adhered to.

• The machine may only be used, maintained, and

operated by persons familiar with and instructed in

its operating and procedures. Arbitrary alterations

to the machine release the manufacturer from all

responsibiliy for any resulting damages.

• The machine may only be used with original acces-

sories made by the manufacturer.

Please note that our equipment has not been desig-

ned for use in commercial, trade or industrial appli-

cations. Our warranty will be voided if the equipment

is used in commercial, trade or industrial businesses

or for equivalent purposes.

5. Safety information

Attention! The following basic safety measures must

be observed when using electric tools for protection

against electric shock, and the risk of injury and re.

Read all these notices before using the electric tool

and keep the safety instructions for later reference.

Safety information

• Warning: When using electric tools it is imperative

to take the following basic safety precautions in or-

der to reduce the risk of electric shock, injury and

re.

• Take due note of all this information before and

while working with the machine.

• Do not lose these safety regulations.

• Guard against electric shock Avoid body contact

with earthed parts.

• When equipment is not being used it should be kept

in a dry, closed place out of childrens reach.

• Keep mounted attachments sharp and clean to

enable you to work well and safely.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DM-ABS1200E - Dineiger in the language / languages: English, German as an attachment in your email.

The manual is 6.74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach DM-ABS1200E - Dineiger Manual

Product: