Manual Scheppach Di1050 (page 16 of 56) (English, German, French, Polish)

782596

Zoom out

Zoom in

1/56

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

16 І GB

Switch position stage 1

Speed range: High torque, low speed

Switch position stage 2

Speed range: Low torque, high speed

Attention! Do not perform this setting during

drilling.

Preselecting the speed (Fig. 1)

1. The speed adjustment dial (9) allows you to dene

the maximum speed.

2. Set the speed adjustment dial (9) to the desired po-

sition.

3. If the on/off switch (10) is fully depressed, the motor

will still only turn as fast as the setting on the speed

adjustment dial (9).

4. This setting can also be adjusted during operation.

Set the direction of rotation (Fig. 1)

The device’s direction of rotation can be changed

with the rotational direction switch.

1. Wait for the device to shut-down.

2. Push the rotational direction speed (8) into the de-

sired position:

Clockwise rotation: to drill and screw in screws.

Anticlockwise rotation: to loosen screws.

Changeover drilling/impact drilling (Fig. 1)

1. Wait for the device to shut-down.

2. Set the changeover switch (1) to the “Drill” symbol.

3. Impact drilling: Set the changeover switch (1) to the

“Impact drill” symbol.

Practical tips

• Always use the proper tool.

• Immediately switch of the device, if the tool should

get jammed. Change the rotation direction to an-

ticlockwise rotation and the carefully unscrew the

jammed tool.

• Do not use any blunt or damaged tools or acces-

sories.

Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies

with the applicable VDE and DIN provisions.

The customer‘s mains connection as well as

the extension cable used must also comply with

these regulations.

Important information

In the event of an overloading the motor will switch

itself off. After a cool-down period (time varies) the

motor can be switched back on again.

Damaged electrical connection cable

The insulation on electrical connection cables is of-

ten damaged.

This may have the following causes:

The additional handle is equally suited for right and

left-handed person.

Mount/set depth stop (Fig. 4)

The boreholes can be precisely drilled to an exact

drilling depth x using the depth stop.

1. Press the depth stop release (4).

2. Use the depth stop (4) in the additional handle (7).

Make sure that the ute of the depth stop (4) en-

gages the ute of the additional handle (7).

3. Place the tip of the depth stop (3) to the desired

drilling depth x behind the tip of the drill.

4. Let go of the depth stop release (4). The depth stop

(3) is now locked.

5. Drill the hole until the depth stop (3) comes in con-

tact with the component part.

Inserting/replacing the tool (Fig. 1)

1. Open the keyless chuck (5) wide (RELEASE) so

that the tool can be inserted. To do so, rmly hold

the rear sleeve (5b) of the keyless chuck (5) and

turn the front sleeve (5a) in the anti-clockwise di-

rection.

2. Insert the tool as far as possible into the keyless

chuck (5).

3. Close the keyless chuck (5) (GRIP) in order to

clamp the tool. To do so, rmly hold the rear sleeve

(5b) of the keyless chuck (5) and turn the front

sleeve (5a) in the clockwise direction.

4. To remove the tool again, rotate the keyless chuck

(5) and pull out the tool.

Always use a universal bit holder use using a screw-

driver bits.

Operation

Do not use the device without the additional han-

dle. It provides additional hold and reduces the

risk of injury.

Observe noise control and local regulations.

Switching on and off (Fig. 1)

1. Connect the machine to the power supply. Make

sure that the net voltage matches the voltage rating

indicated on the device’s type plate. Switching on:

Press the on/off switch (10).

2. By using the on/off switch (10)) you can progres-

sively control the speed.

Gentle pressure: low speed

Increase pressure: higher speed.

3. Continuous operation: Press the lock button (12).

The on/off switch (10)) is locked.

4. Switching off: Release the on/off switch (10). For

continuous operation, briey press the on/off switch

(10).

Dening the speed range (Fig. 1)

The gear selector switch (2) allows you to work within

a specic speed range.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Di1050 in the language / languages: English, German, French, Polish as an attachment in your email.

The manual is 2.94 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach Di1050 Manual

Product: