781464

Scheppach Deco Flex Manual

19
Zoom out
Zoom in
Previous page
1/108
Next page
19
faible niveau de vibration et de bruit. Taille ideale
400 x 240 mm.
REMPLACEMENT DES LAMES DE SCIE
AVERTISSEMENT: Pour éviter des blessures dues à la mise
en marche non intentionnelle de la scie. débranchez la scie
et retirez la fiche de contact avant de commencerle montage
de la scie.
A. Lames de scie plates
Utilisez l’adaptateur (fig 6) avec les lames de scies
plates.
La lame de scie est fixée avec des vis creuses.
A 1 Enlevage de la lame de scie, fig. 7+8
• Retirez la lame de scie en glissant en haut
l’incrustation de la table, alors dévissez le tendeur (1).
• Appuyez le bras supérieur en bas légèrement fig. (10).
• Alors enlevez la lame de scie en la retirant des supports
et à travers la perforation d’accès dans la table.
A 2 Insérer la lame de scie :
• Placez la lame de scie avec les deux adaptateurs
dans le support inférieur, l’autre bout en el support
supérieur.
• Appuyez le bras supérieur en bas légèrement fig. (10)
avant de l’accrocher.
• Serrez la lame avec le tendeur (1) (fig. 11) en la
tournant dans le sens des aiguilles d’une montre.
Contrôlez le serrement de la lame. Continuez à faire
la tourner dans le sens des aiguilles afin de serrer la
lame de plus.
REMARQUE: Si la lame est trap tendue, le rabinet est difficile
à auvrir de nouveau.
B. Lame de scie avec des épingles
B 1 Enlevage de la lame de scie, Fig. 7 + 8
• Retirez la lame de scie d’abord en dévissant le tendeur
(1).
• Enlevez la lame de scie du support supérieur et de
l’inférieur en appuyant en bas légèrement sur le bras
supérieur de la scie (fig. 10).
CHANGING THE SAW BLADES
Warning: Switch off the saw and remove the mains supply
plug before installing saw b!ades in order to avoid injuries
caused by unintentiona! activation of the saw.
A. Flat saw-blades
Use the adapter (fig. 6) with flat saw-blades.
The saw-blade is fixed with Allen screws.
A 1 Saw-blade removal, fig. 7+8
• Extract the saw-blade by sliding the table’s inlay up,
then unscrew the tightening screw (1).
• Slightly press the upper arm (5) down (fig. 10).
• Then remove the sawblade by pulling it forward out
of the supports and through the access perforation
in the table.
A 2 Inserting the saw-blade:
• Put the saw-blade with the two adapters into the lower
support, the other end into the upper support.
• Slightly press the upper arm (5) down (fig 10) before
hooking it in.
• Tighten the blade with the tightening screw (1) (fig.
11) by rotating it clockwise. Check the tightness of the
blade. Keep on rotating clockwise in order to tighten
the blade even more.
B. Saw-blade with pins
B 1 Saw blade removal, fig. 7 + 8
• Extract the saw-blade by first unscrewing the tightening
screw (1).
• Remove the saw-blade from the upper and lower
support by slightly pressing the saw´s upper arm down
(fig. 10).
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Deco Flex at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Deco Flex in the language / languages: English, German, French, Italian, Polish, Finnish as an attachment in your email.

The manual is 2.9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info