782185
10
Zoom out
Zoom in
Previous page
1/92
Next page
english 11
maining hazards which are not yet evident may still be
present.
• Remaininghazardscanbeminimizedbyfollowingthe
instructionsin„SafetyPrecautions“,„ProperUse“and
in the entire operating manual.
• Donotforcethemachineunnecessarily:excessivecutt
ing pressure may lead to rapid deterioration of the blade
anda decreasein performance in terms of nish and
cutting precision.
• Avoid accidental starts: do not press the start button
while inserting the plug into the socket.
Scroll Saw Design Features, Fig. 1
1 Quick release and tension lever: forquicktensioningand
removalot the saw blade with a handle on the lever.
2 Blade guard: protects your hands from injury.
3 Work piece holder
4 Shavings blower: keeps the workpiece area free from
dust.
5 decotronic: electronical speed switch
deco 402: Speed switch
6 On/Off switch
7 Angle scale: you can read the angle position of the table
with this scale.
Installation
Setting the saw bench, Fig. 2
Setting the angle scale
• Releasethestarbuttonandbringthesawbench(2)toa
rightangle(3)inrelationtothesawblade.
• Use a 90° angle tc measure the right angle between
thebladeandthebench.Thesawbladebe90°tothe
angle.
• Closethestarbuttonagainwhenthedistancebetween
thebladeandthe90°angleisataminimum.Thebench
shouldthenbeat90°tothesawblade.
• Releasethe lockscrew andbringthe indicatorto the
zero position. Fasten the screw. Please note: the angle
scaleisausefulpieceofsupplementaryequipment,but
should not be used for precision work. Use scrap wood
for saw tests, adjust the bench if neces sary.
Note: The bench should not be on the motor block, this can
cause undesireable noise.
Horizontal saw bench and diagonal cuts, Fig. 2+3
• Thesawbenchcanbepositionedintoa450diagonal
position or be left in the horizontal position.
• Youcanreadofftheapproximateslopeanglebyusing
the angle scale located under the work bench. For more
exact adjustment, use scrap wood for some saw tests;
adjust the bench if necessary.
Blade guard assembly, Fig. 4
Install the blade guard to the holder as shown in the dia-
gram. Secure the screws with a nut and washer.
• Liftthesawontotheframeandbaseandpushitonto
the workbench.
• Familiarizeyourselfwiththesawoperatingelementsand
features.
Mounting the saw on a work bench, Fig. 5
• Aworkbenchmadefromsolidwoodisbetierthanone
made of plywood, as interfering vibrations and noise are
more noticeable with plywood.
• Thenecessarytoolsandsmallpartsforassemblingthe
saw on a workbench are not supplied with the saw. How-
ever,useequipmentofatleastthefollowingsize:
1 Saw body
2 Foam rubber base
3 Work bench
4 Flat seal
5 Washer
6 Hexagonal nut
7Locknut
8 Hexagonal bolt
Ouantity Description
4Hexagonalbolts(6mm)1/420xlength
4Flatseal(7mm)9/321.0
4Washers(7mm)9/321.0.
8Hexagonalnuts(6mm)1/420
First of all, drill holes into the seating surface and then
insert the screws.
• Afoamrubberbaseforreductionofnoiseisnotsupplied
with the saw either. However, we expressly recommend
that you use such a base to keep vibration and noise to
a minimum. Ideal size 410 x 320 mm.
Changing the saw blades
Warning: Switch off the saw and remove the mains supply plug
before installing saw b!ades in order to avoid injuries caused
by unintentiona! activation of the saw.
A. Flat saw blades
A.1 Removing the saw blades, Fig. 7
1 First af all, release the tension via the tensianing tap ta
remave the saw blade.
2Undothescrewsetontheupperbladeholder(Fig.8).
3 Undo the lower holder. To do this, use the spanner which
you can feed through the saw blade slot.
4Removethesawbladebypullingitforwards fromthe
holders and by pulling it through the access hole in the
bench(Fig.9).
A.2 lnstalling the saw blade
1Wheninstallingthesawblade,rstofallpullitthrough
the saw blade slot in the work bench.
Note: In order to avoid tearing or lifting of lightweight work-
pieces, the saw blade teeth should always face down towards
the work bench.
2 Guide the saw blade into the lower holder and fasten the
screws(Fig.9).
3 Guide the other end of the blade into upper holder and
fasten the screws. Push the upper arm of the saw slight-
lydownwardsbeforetighteningthescrews(Fig.10).
4 Tension the blade by turning the tensioning tap clock-
wise.Checkthebladetension.Carryonturningclock-
wisetotensionthebladefurther(Fig.11).
Note: It is difficult to open the tensioning tap again if the blade
is too tightly tensioned.
Saw blade with pins
Note: The upper and lower holders should not be tightened
too much when using saw blades which have pins. The gap
between the holding blocks must be slightly wider than the
saw blade. After installation, the blade is held in place by the
tensioning device.
B.1 Removing the saw blade, Fig. 7
1 First of all, release the tension tap.
2 Take the saw blade out from the upper and lower holder.
Push the upper arm of the saw slightly downwards be-
fore tightening the screws.
B.2 Installing the saw blade
1 Guide one end of the saw blade through the borehole in
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Deco 401 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Deco 401 in the language / languages: All languages as an attachment in your email.

The manual is 2.91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info