Manual Scheppach CSE2500 (page 30 of 200) (English, German, Dutch, French, Italian, Polish, Spanish)

781410

Zoom out

Zoom in

1/200

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

30 | GB

• After working with the chainsaw, you should always:

Clean the saw chain and guide bar and replace the

chain guard.

• If the chain brake is activated the chainsam will be

deactivated immediately.

Explanation of the Operation/Overload indicator

(Fig. 2, 18):

Green LED:

The green LED comes on when the device is in use.

Red LED:

The red LED comes on if the device is overloaded.

It does not go out until the device is switched off and

back on again.

8. Initial operation

The voltage and current supply must comply with the

ratings on the type plate.

Before commencing work, always check that the

chainsaw works properly and is safe to operate.

Check also that the chain lubrication and the oil

gauge are in good working order (see Fig. 4). When

the oil lever is approx. 5 mm from the bottom mark,

you must top up with oil. When the oil level is higher

you can work without worry.

• Switch on the chain saw and hold it above the

ground. Be careful not allow the chainsaw to touch

the ground. For safety reasons it is best to keep a

clearance of at least 20 cm. If you now see growing

traces of oil, the chain lubrication system is work-

ing correctly. If there are no traces of oil at all, try

cleaning the oil outlet (Fig 2, C) and the oil duct or

contact your Customer Service. (Be sure to read

the section “Filling in chain oil and chain lubrication”

on this point).

• Check the chain tension and retention, if necessary

(see the section “Tensioning the saw chain” on this

point).

• Make sure the chain brake is working properly (see

also the section “Releasing the chain brake”).

Assembly

Fitting the guide bar and chain (Fig. 1, 2, 3)

Warning! If the chain saw is already connected to

the power supply: Pull the plug from the socket outlet.

Wear protective gloves whenever doing any work on

the saw chain.

Important: The front nger guard (3) must always be

in the top (vertical) position (Fig. 5).

The guide bar and saw chain are supplied separately.

To assemble, rst unscrew the lock nut (SDS-sys-

tem/5) and remove the guide bar cover (6). The guide

bolt (17) must be in the centre of the guide.

If necessary, adjust the chain tensioning with the

chain wheel (Fig. 3, 5a).

Warning! To prevent injury on the sharp cutting edg-

es, always wear gloves when assembling, tensioning

and checking the chain.

Before assembling the guide bar with the saw chain,

check the cutting direction of the teeth!

The running direction is marked with an arrow on the

cover (6). To determine the direction of cut, it may be

necessary to turn over the saw chain (4).

Hold the guide bar (7) vertically with the tip pointing

upwards and put on the saw chain (4, beginning at

the tip of the bar.

Then assemble the guide bar with the saw chain as

follows:

• Place the guide bar with the saw chain on the chain

wheel (16) and guide bolt (17). Ensure that the ad-

justment plate (Fig. 3/7a) is showing to you.

• Place the saw chain round the chain wheel (16).

Cause the chainsaw to the sprocket and check

whether it is correctly.

• The adjustment plate (7a) is fastened to the guide

rail (7) with the screw F.

• Place the cover (6) on top and tighten gently with

the lock nut (5).

Now the saw chain has to be correctly tensioned.

Tensioning the saw chain

Warning!

Always pull the plug out of the power socket before

doing any work on the chainsaw!

Wear safety gloves!

• Make sure the saw chain (4) is inside the guide

groove of the guide bar (7).

• Turn the outer Knob (Fig. 3/5a) clockwise until the

saw chain is correctly tensioned, then rotate the in-

side knob (5) to block the guide bar in that position.

• While the inside knob is being tightened, the guide

bar must then be pushed upwards.

• Check the chain tension again. Do not tension the

chain too tightly.

• When cold, it should be possible to lift the chain in

the middle of the guide bar approx. 5 mm. Tighten

the lock nut (5) securely.

• When warm, the saw chain will expand and slacken

and there is a danger of it jumping off the rail alto-

gether. Re-tension if necessary.

• If the saw chain is re-tensioned when hot, it must

be loosened again when the sawing work has been

completed.

• Otherwise, the contraction which takes place as

the chain cools would result in excessively high

tension.

• A new saw chain requires a running-in period of

approx .5 minutes. Chain lubrication is very impor-

tant at this stage. After running in, check chain ten-

sion and re-tension if necessary.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach CSE2500 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 8.36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach CSE2500 Manual

Product: