781410

Scheppach CSE2500 Manual

29
Zoom out
Zoom in
Previous page
1/200
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB | 29
• Use a surge protector with a release current of
30 mA or less.
• Have your power tool serviced by a qualied repair
person using only identical replacement parts.
• Carefully follow the maintenance, control and ser-
vice instructions in this manual.
• Practise using the saw (sawing logs on a saw-
horse) and get an experienced user or a specialist
to explain to you the function of the saw, the way of
working, the techniques of sawing and the personal
protection equipment.
6. Technical data
Cutting data chainsaw
Cutting lenght 45,5 cm
Bar lenght 45,7 v
Capacity oiltank 0,125 l
Type of oil wear resistant oil
Saw chain division 3/8"
Drive link thickness 1,27 mm
Saw chain type Oregon
91PX062X
Number of teeths drive
sprocket 6
Tooth pitch of drive sprocket 3/8"
Chain brake yes
Guide bar type Oregon
180SDEA041
Engine
Motor 230-240 V / 50 Hz
Power 2400 W
Cutting speed max. 14 m/s
Weight 5,5 kg
Weight without bar and chain 4,8 kg
Subject to technical changes!
Information concerning noise emission measured
according to relevant standards:
Sound pressure LpA = 93 dB(A)
Sound power LWA = 104,6 dB(A)
Guaranteed Sound power LWA = 106 dB(A)
Uncertainty KPA = 3 dB(A)
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Vibration Ahv (front handle) = 7,5 m/s2
Vibration Ahv (rear handle) = 7,5 m/s2
Uncertainty KPA = 1,5 m/s2
• The specied vibration emission value has been
measured according to a standardised testing pro-
cedure and can be used for comparison of one
electric tool with another;
• The specied vibration emission value can also be
used for an initial assessment of the load.
Warning:
• The vibration emission value can vary from the
specied value during the actual use of the elec-
tric tool, depending on the type and the manner in
which the electric tool is used;
• Try to minimise stress from vibrations as low as
possible. Some examples of means for reducing
the vibration stress are wearing gloves while us-
ing the tool and limiting work time. In the process
all parts of the operating cycle must be taken into
account (such as times in which the electric tool is
switched off or time in which it is switched on, but is
not running under a load).
7. Attachment and operation
Warning!
Always wear safety goggles, ear muffs, protective
gloves and heavy-duty work clothes! Use the saw
only with approved extension cables with the pre-
scribed insulation and connections designed for out-
door use (approved rubber-sheathed cables) which t
the chainsaw plug.
The chain saw is equipped with safety switches, re-
quiring the use of both hand. The chainsaw works
only when one hand is pushing the button 11 and 13
at the same time. If the chainsaw does not run, the
chain brake must be released at the front nger guard
(3). Be sure to read the sections “Chain brake” and
“Releasing the chain brake “ on this point.
To switch on:
• Release the chain brake (3), push in the lock (11)
and press the power switch (13).
• Place the lowest claw (Fig 2, J) on the wood . Raise
the chain saw by the rear grip (1 ) and saw into the
wood. Move the chain saw back a little and place
the claw further down.
• Be careful when sawing splintered wood as pieces
of wood may be ripped off.
After switching on, the chainsaw will run immediately
at high speed .
To switch off
• Release either the ON/OFF switch (13) on the rear
grip.
• The release of ON/OFF switch results the stop of
the chainsaw within 1sec., and heavy sparkling.
This is normal and safe for the proper operation of
the chainsaw.
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach CSE2500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach CSE2500 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 8.36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info