Manual Scheppach cs 55 (page 15 of 105) (All languages)

644559

Zoom out

Zoom in

1/105

Make sure that there has not been a voltage failure in the

electrical system.

ADJUSTING

Caution: Prior to carrying out one of the following adjust-

ment steps, switch the machine off and unplug the mains

plug.

Cutting depth adjustment, Fig. 2

The cutting depth can be adjusted from 0 to 55 mm.

Unfasten the cutting depth adjustment screw (6) and set

the required depth using the scale (7) and retighten the

screw.

The dimentions on the rail shows the cutting depth with-

out rail.

Mitre settings, Fig. 3

The mitre square can be set from 0° to 45°.

Unfasten the mitre adjustment screws (8) on both sides,

set the desired mitre square on the scale (9) and retight-

en both screws.

Saw blade replacement, Fig. 4, 5, 6

1 Press the plunge-cut trigger (3) and push down the saw

blade towards the saw blade replacement position until

the locking lever (15) locks in place in the front hole.

2 Press on the shaft lock (13) and rotate the saw blade

(10) until the lock clicks into place.

3 Keep the shaft lock (13) pressed and open the saw

blade locking screw (17) by turning it counter-clock-

wise.

4 Remove the outer ﬂange (16) and the saw blade (10).

(Caution: risk of injuries, wear protective gloves)

5 Insert the new blade and ﬂange

6 Screw in and tighten the saw blade locking screw while

keeping the shaft locking mechanism pressed again

7 Slightly press the handle (1) downwards, release the

locking lever (15) and bring the saw into the initial

position.

Adjusting the splitting wedge, Fig. 7

Adjust the distance between saw blade and splitting

wedge after a saw blade replacement, or whenever neces-

sary.

Put the saw in the same position as you do when replac-

ing a saw blade.

Unfasten the adjustment screw (18) using an Allen key

and set the splitting wedge 2-3 mm higher than the saw

blade, then retighten the adjustment screw.

Operations

After having performed all the above procedures and

opera tions, you may begin cutting.

ATTENTION: Always keep hands away from the cutting

area and do not try to approach it when the machine is

running.

Switching the product on/off, Fig. 1

To switch the plunge-cut saw on, press the on/off switch

• Even when all safety measures are taken, some re-

maining hazards which are not yet evident may still

be present.

• Remaining hazards can be minimized by following the

instructions in „Safety Precautions“, „Proper Use“ and

in the entire operating manual.

• Do not force the machine unnecessarily: excessive

cutt ing pressure may lead to rapid deterioration of the

blade and a decrease in performance in terms of ﬁnish

and cutting precision.

• When cutting aluminium and plastics always use the

app ro priate clamps: all workpieces must be clamped

down ﬁrmly.

• Avoid accidental starts: do not press the start button

while inserting the plug into the socket.

• Always use the tools recommended in this manual to

obtain the best results from your plunge cut saw.

• Always keep hands away from the work area when the

ma chine is running; before performing tasks of any

kind release the main switch button located on the

handgrip, thus disconnecting the machine.

m Suitable use

To cut:

• Hard and soft, domestic and exotic wood both longitu-

dinally and transversally and with appropriate adjust-

ments (speciﬁc blade and clamps);

Unsuitable use

Do not cut:

• Ferrous materials, steel and cast iron or any other ma-

terial not mentioned above and in particular foodstuffs.

Start-up

Observe the safety notes in the operating instructions before

operating the machine.

REMOVAL OF PACKAGING

Remove the box used to protect the machine during

trans portion and keep it intact for future transportation

and storage.

ELECTRICAL CONNECTIONS

Check that the electrical system to which the machine is

connected is earthed in compliance with current safety

regulations and that the current socket is in perfect con-

dition.

The electrical system must be ﬁtted with a magnetother-

mal protective device to safeguard all conductors from

short circuits and overload.

The selection of this device should be in line with the

following electrical speciﬁcations of the machine stated

on the motor.

NOTE: Your plunge cut saw’s electrical system is equipped

with an undervoltage relay which automatically opens the

circuit when the voltage falls below a minimum pre-est-

ablished limit and which prevents the self-reset of ma-

chine functions when voltage returns to normal levels.

If the machine stops involutarily, do not be allarmed.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach cs 55 in the language / languages: All languages as an attachment in your email.

The manual is 3,87 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach cs 55 Manual

Product: