781648

Scheppach CDD45-20ProS Manual

22
Zoom out
Zoom in
Previous page
1/76
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
22 | GB
Hard screwdriving conditions (into metal):
Particularly high torques can occur, for example with
metal screws tightened by socket tool bits. Select a
lower rotation speed.
Soft screwdriving conditions (e.g. into soft
wood):
You should also select a low speed in order not to
damage the wood workpiece surface through contact
with the metal screw head.
Use a countersinker.
When drilling into wood, metal and other materials, take
note of the following advice: With small diameter drill
bits use a high drill speed. For large diameter drill bits,
use a low drill speed. For hard materials, select a low
drill speed. For soft materials, select a high drill speed.
Secure or x down the workpiece (if possible) in a
clamp or vice.
Mark the intended position of the hole with a centre
punch or a nail and select a low drill speed for drilling.
Take the rotating drill bit out of the hole frequently so
that swarf or drill dust can be re-moved and the hole
and tool is ventilated.
Drilling in metal:
Use a metal drill bit (HSS). For the best results, you
should cool the bit with oil.
Metal drill bits can also be used to drill into plastic.
Drilling in stone:
Use a circular shafted masonry drill bit with a hard-
ened metal tip.
Drilling in wood:
Normally you should use a wood drill with a cen-
tring point. For deep holes, use an auger type bit.
For large diameter holes, use a forstner bit. You can
screw small screws into soft wood without the need
for pre-drilling.
12. Cleaning
Danger!
Always pull out the battery pack before starting any
cleaning work.
• Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
• We recommend that you clean the device immedi-
ately each time you have nished using it.
• Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep into
the device. The ingress of water into an electric tool
increases the risk of an electric shock.
13. Storage
Store the device and its accessories in a dark, dry
and frost-proof place that is inaccessible to children.
The optimum storage temperature is between 5 and
30˚C. Store the electrical tool in its original packag-
ing. Cover the electrical tool in order to protect it from
dust and moisture. Store the operating manual with
the electrical tool.
14. Maintenance
There are no parts inside the equipment which re-
quire additional maintenance.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: carbon brushes
* Not necessarily included in the scope of delivery!
15. Disposal and recycling
The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The equip-
ment and its accessories are made of various types
of material, such as metal and plastic. Defective com-
ponents must be disposed of as special waste. Ask
your dealer or your local council.
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach CDD45-20ProS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach CDD45-20ProS in the language / languages: English, German, French, Polish as an attachment in your email.

The manual is 3.91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info