781648

Scheppach CDD45-20ProS Manual

21
Zoom out
Zoom in
Previous page
1/76
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB | 21
10. Construction
Warning!
Always remove the battery pack before making ad-
justments to the equipment.
11. Installation
m Important!
You must fully assemble the appliance before using it
for the rst time!
To ensure that the Li battery pack provides long ser-
vice you should take care to recharge it promptly. You
must recharge the battery pack when you notice that
the power of the cordless equipment drops.
Insertion / removal of a batterypack into the ap-
pliance
Ensure that the appliance is switched off before in-
serting the battery. The insertion of a battery into an
electrical appliance that is switched on can lead to
accidents.
Inserting the rechargeable battery pack:
Move the rotation switch (2) into the middle position
(lock) and push the rechargeable battery pack (5) into
the handle until it engages.
Removing the rechargeable battery pack:
Press the release button (6) and remove the re-
chargeable battery pack.
Used batteries
If a fully recharged battery lasts for considerably
shorter operating times, the battery is used up and
needs to be replaced. Only use an OEM battery pack
replacement available from our Customer Service.
Changing tools
• Your cordless electric drill / screwdriver has a fully
automatic spindle lock and is tted with an enclosed
keyless chuck incorporating the latest technology.
Once the motor has come to a halt, the drive shaft
is automatically locked, so that the chuck (9) can be
opened simply by turning it . After you have insert-
ed the required bit and xed it in place by turning
the chuck , you can immediately continue working.
The spindle lock releases itself automatically when
the motor is started (by operation of the ON / OFF
switch (3) ).
Torque pre-selection
• You can adjust the torque by using (8) torque prese-
lection.
• Select a low setting for small screws, soft workma-
terial.
• Select a high setting for large screws, hard work
materials and for the extraction of screws.
• For drilling, push the selector to the setting for drill-
ing, in that you adjust the torque pre-selector to the
position .
• For drilling tasks, also push the gear selector switch
(1) to the front (Position: 2).
2 Gear Drive
CAUTION! Move the gear selector switch (1) only af-
ter the device has come to a standstill. Failure to ob-
serve this advice may result in damage to the device.
In the rst gear (Gear selector switch (1) in Position:
1) This setting is intended for use with all screwing
tasks and for accessories (see example Fig. B).
In the second gear (Gear selector switch (1) in Posi-
tion: 2) for the carrying out of drilling tasks (see ex-
ample Fig. A).
Installation
Switching On /Off
Switching on:
To start the appliance squeeze on the ON / OFF switch
(3) and then keep it pressed down. The LED working
light (7) comes on with a slightly or fully pressed ON /
OFF switch (3) and illuminates the working area in
poor lighting conditions.
Switching off:
To stop the appliance, release the ON / OFF switch (3).
Adjusting the speed
The ON / OFF switch (3) has a variable speed control
device. Slight pressure on the ON / OFF switch (3)
will cause the rotation speed to slow down. With in-
creased pressure, the rotational speed will increase.
Note: The integrated engine brake means that the
device will come to a fast standstill.
Switching direction of rotation
To switch the direction of rotation, push the direction
of rotation switch (2) to either the right or to the left.
Tips and Tricks
Before you use the appliance, check to see that the
screw or drill bit is properly tted, i.e. located centrally
in the chuck. Screw bits are designated with their di-
mensions and their shape. If you are unsure, always
try the particular screw bit out to see whether it sits in
the screw head without any free play.
Torque:
Smaller screws and bits in particular can be easily
damaged if you adjust the appliance with too high a
torque and/or rotation speed.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach CDD45-20ProS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach CDD45-20ProS in the language / languages: English, German, French, Polish as an attachment in your email.

The manual is 3.91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info