781689

Scheppach CAG115-20ProS Manual

27
Zoom out
Zoom in
Previous page
1/92
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB | 27
For grinding or cutting wheels up to approx. 3
mm thick: Screw on the ange nut with the at side
facing the grinding or cutting wheel.
10.3.2 Flange arrangements when using grinding
wheels and cutting wheels (Fig. 5)
• Mount guard (1), clamping ange (a), wheel (7) and
ange nut (b) as shown in Fig. 5.
• The arrows indicate the mounting direction.
10.4 Motor
It is vital for the motor to be well ventilated during op-
eration. Be sure, therefore, to keep the ventilation
holes clean at all times.
10.5 Grinding wheels
• Never use a grinding or cutting wheel bigger than
the specied diameter.
• Before using a grinding or cutting wheel, check its
rated speed.
• The maximum speed of the grinding or cutting
wheel used must be higher than the idle speed of
the angle grinder.
• Use only grinding and cutting wheels that are ap-
proved for a minimum speed of 8,500 rpm and a
peripheral speed of 52 m/sec.
• Check the direction of rotation when you use dia-
mond cutting wheels. The directional arrow on the
diamond cutting wheel must point in the direction
in which the tool rotates.
Take special care that the grinding/cutting wheels
are properly stored and transported. Ensure that the
grinding/cutting wheels are never exposed to shock,
jolts or sharp edges (for example during transport
or storage in a toolbox). This could cause damage
(such as cracks) to the grinding/cutting wheels and
place the user in serious danger.
11. Operating instructions
When working with the device, always wear suit-
able clothing and appropriate protective equip-
ment. Prior to each use it must be ensured that
the device is working correctly. Personal protec-
tive equipment and a fully functional device re-
duce the risk of injuries and accidents.
11.1 Rough grinding
m WARNING
Use the safety device for grinding
For the best rough grinding results, hold the grind-
ing wheel at an angle of between 30° and 40° to the
workpiece surface and guide back and forth over the
workpiece in steady movements.
11.2 Cutting
m WARNING
Use the safety device for abrasive cutting
When you use the right-angle grinder for cutting pur-
poses, avoid tilting it in the cutting plane. The cutting
wheel must have a clean cutting edge. A diamond
cutting wheel is best used to cut hard stone.
m It is prohibited to use the machine on asbes-
tos materials!
m Never use a cutting wheel for rough grinding.
12. Cleaning, storage and
maintenance
m WARNING
Always pull out the battery pack before starting
any cleaning work.
12.1 Cleaning
• Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
• We recommend that you clean the device immedi-
ately each time you have nished using it.
• Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep into
the device. The ingress of water into an electric tool
increases the risk of an electric shock.
12.2 Storage
Store the device and its accessories in a dark, dry
and frost-proof place that is inaccessible to children.
The optimum storage temperature is between 5 and
30˚C. Store the electrical tool in its original packag-
ing. Cover the electrical tool in order to protect it from
dust and moisture. Store the operating manual with
the electrical tool.
12.3 Maintenance
There are no parts inside the equipment which re-
quire additional maintenance.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: Grinding wheels
* Not necessarily included in the scope of delivery!
13. Disposal and recycling
The equipment is supplied in packaging to prevent it
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach CAG115-20ProS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach CAG115-20ProS in the language / languages: English, German, French, Polish as an attachment in your email.

The manual is 4.11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info