782179

Scheppach BSH500 Manual

17
Zoom out
Zoom in
Previous page
1/28
Next page
english
11
Assembly
Assembly tools
Blade key
Holding mandril
Hex pin wrench (Wrench size 5 / 6 included in delivery)
Open-end wrench (Wrench size 7, 8, 10, 13, 17)
Screw driver not included in delivery
Due to technical packing reasons, your scheppach machine
does not come completely assembled.
Lower saw blade cover, clamp angle, Fig. 01
•
Screw the pivoting bracket (1) onto the adjustment
frame in the following order.
Large washer
Pivoting bracket (1)
Small washer ø 8
Hex nut M8 self-locking
•
The pivoting bracket must be freely moveable.
•
Screw together screw down cover (2) and guard plate
(3).
3 cheese-head screws M 4 x 10
3 serrated edge washers A 4.3
3 hex nuts M4
•
Screw on guard plate (3) and pivoting bracket (1).
4 hex bolts M6x12
4 serrated edge washers A 6.4
4 hex nut M6
•
Attach both clamp angles (4)
4 hex bolts M8x 12
4 serrated edge washers A 8.4
Hand wheel, Switch unit, Switch plug combination, Fig. 02
Screw the hand wheel onto the adjusting spindle.
1 washer 8
1 cap nut M8
Switch unit 400 V
1 hex bolt M8 x 16
1 serrated edge washer A8.4
1 hex nut M8
Switch plug combination three-phase
2 raised-head screws M 4 x 50
2 washers ø 4
2 serrated edge washers A 4.3
2 hex nuts M 4
Frame legs, Cross-cutting guide, Fig. 03
•
Insert frame legs with spacing angle (5) into the table
corners and adjust the screws loosely.
each 1 cheese-head screw M8 x 100
each 1  ller piece (6)
each 1 stay piece (7)
each 1 serrated edge washer A 8,4
each 1 hex nut M8
as well as
each 2 carriage bolts M8 x 60 with serrated washers and
hex nuts.
Make sure to attach the cross-cutting guide onto the right side
of the table at the same time.
•
Slide the rubber ring (8) and the cross-cutting guide
onto the guide rail.
Screw the front bracket (9) onto the guide rail.
1 serrated edge washer 10.5
1 hex nut M10
Insert the rear bracket (11) onto the guide rail.
U-bolts
•
Attach both U-bolts (10) diagonally to each other.
each 2 serrated edge washers 10.5
each 4 hex nuts M10
Longitudinal and diagonal braces, Fig. 04
Note insertion position as it corresponds to the diagonal
position of the frame legs.
•
First attach the braces lightly with screws
each 1 cheese-head screw M8 x 45
each 1  ller piece (6)
each 1 brace clamp (11)
each 1 serrated edge washer 8.4
each 1 hex nut M8
Then tighten all screws and nuts on the frame legs and
braces. Place the machine on its legs.
Clamping attachment for ripping fence, Fig. 05
•
Attach the clamping attchment (1) for the ripping
fence
2 cheese-hex screws M6 x 30
2 serrated edge washers 6,4
2 hex nuts M6
Cross-cutting guide, Fig. 05
•
Insert a carriage bolt M8 x 70 from beneath the rect-
angular tube into the cross-cutting guide. Clamp the
cross-cutting guide with washer 8 and the hand wheel.
With the hex bolt in the rectangular tube, adjust the
swivel component at a right angle to the saw blade.
Noise parameters
The noise emission values at the work place, determined
according to EN 23746 (acoustic power levels) and EN
31202 (acoustic pressure levels) with a correction factor
k3 calculated according to appendix A.2 of EN 31204,
based on operating conditions listed in ISO 7904,
appendix A, are:
bsh 400
Acoustic power level in dB
Idling L
WA
= 93.9 dB(A) Operating L
WA
= 101.8 dB(A)
Acoustic pressure level in dB
Idling L
pAeq
= 79.7 dB(A) Operating L
pAeq
= 91.3 dB(A)
bsh 500
Acoustic power level in dB
Idling L
WA
= 100.7 dB(A) Operating L
WA
= 108.3 dB(A)
Acoustic pressure level in dB
Idling L
pAeq
= 88.3 dB(A) Operating L
pAeq
= 95.8 dB(A)
A measuring uncertainty coef cient (K = 4 dB) applies to
the emission values listed above.
Dust emmision parameters
The dust emmision parameters, measured according to the
principles for measuring dust emmisions (concentration
parameter) for woodworking machines speci ed by the
German wood professional committee, are below 2 mg/m
3
.
Dust emmissions can therefore be continuously kept
within the range allowed under currently valid German
regulations by connecting the machine to a vacuum ex-
haust system with an air ow speed of at least 20 m/s.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach BSH500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach BSH500 in the language / languages: English, German, Italian as an attachment in your email.

The manual is 1.49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info