Manual Scheppach BS3000 Primaster (page 26 of 44) (English, German, French)

782175

Zoom out

Zoom in

1/44

26 GB

• For safe work when transverse cutting, use the spe-

cial transverse cutting gauge accessory.

10.1 Performing longitudinal cuts (Fig. A)

Here, a workpiece is cut in its longitudinal direction.

• Position the longitudinal fence (5) on the left side

(if possible) of the saw band, in accordance with

the desired width.

• Lower the saw band guide (4) onto the workpiece.

• Switch on the saw.

• Press one edge of the workpiece against the lon-

gitudinal fence (5) with the right hand, whilst the

at side lies on the saw bench (6).

• Slide the workpiece at an even feed rate along the

longitudinal fence (5) into the saw band.

• Important: Long workpieces must be secured

against tipping at the end of the cutting process

(e.g. with reel-off stand, etc.)

• Attention! When processing narrower workpieces

it is essential to use a push stick.

The push stick (N) must always be stored within

reach, on the hook (i) provided for this purpose on

the side of the saw (Fig. 15).

10.2 Angled cuts (Fig. B+ Fig. 6)

• In order to execute angled cuts parallel to the saw

band, it is possible to tilt the saw bench (6) for-

wards from 0° - 45°.

• Release the locking handle (E).

• Tilt saw bench (6) forwards, until the desired angle

is set on the degree scale.

• Retighten the locking handle (E).

• Attention: With a tilted saw bench (6), the longitudi-

nal fence (5) must be positioned on the downward

facing side to the right of the saw band in the work-

ing direction (if the workpiece width allows this),

in order to secure the workpiece against slipping.

• Perform the cut as described under 10.1.

10.3 Freehand cuts (Fig. C)

One of the most important features of a band saw is

the ease with which it can cut curves and radii.

• Lower the saw band guide (4) onto the workpiece.

• Switch on the saw.

• Press the workpiece rmly onto the saw bench (6)

and slowly slide into the saw band.

• During freehand cutting you should always work

with a low advancing speed, so that the saw band

can follow the desired line.

• In many cases it is helpful to roughly saw curves

and corners approximately 6 mm from the line.

• If it is necessary to saw curves that are too tight

for the saw band used, auxiliary cuts must be sawn

up to the front face of the curve, so that these fall

off as wood waste when the nal radius is sawn.

10.4 Executing cuts with the transverse cutting

gauge (Fig. D + Fig. 18) (optional)

• Set transverse cutting gauge (12) to the desired

angle (see 8.7)

• Perform the cut as described under 10.1.

11. Cleaning and maintenance

Important.

Warning! Prior to any adjustment, maintenance or

service work disconnect the mains power plug!

General maintenance measures

Wipe chips and dust off the machine from time to

time using a cloth. In order to extend the service life

of the tool, oil the rotary parts once monthly. Do not

oil the motor.

When cleaning the plastic do not use corrosive prod -

uct.

Cleaning

• Keep all safety devices, air vents and the motor

housing free of dirt and dust as far as possible.

Wipe the equipment with a clean cloth or blow it

with compressed air at low pressure.

• We recommend that you clean the device immedi-

ately each time you have nished using it.

• Clean the equipment regularly with a moist cloth

and some soft soap. Do not use cleaning agents or

solvents; these could attack the plastic parts of the

equipment. Ensure that no water can seep into the

device. The ingress of water into an electric tool i

creases the risk of an electric shock.

Maintenance

There are no parts inside the equipment which re-

quire additional maintenance.

12. Storage

Store the device and its accessories in a dark, dry

and frost-proof place that is inaccessible to children.

The optimum storage temperature is between 5 and

30˚C.

Cover the electrical tool in order to protect it from

dust and moisture.

Store the operating manual with the electrical tool.

13. Electrical Connection

The installed electric motor is connected and is ready

to work.

The connection complies with the relevant VDE and

DIN regulations.

The customer-side mains supply and the used exten-

sion line must meet these regulations.

Important information

In the event of an overloading the motor will switch

itself off. After a cool-down period (time varies) the

motor can be switched back on again.

Defective Electric Connection Lines

Often, insulation damages occur on electrical con-

nection lines.

Causes are:

1 Drag marks if connection lines are led through win-

dow or door clearances.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach BS3000 Primaster in the language / languages: English, German, French as an attachment in your email.

The manual is 3.93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach BS3000 Primaster Manual

Product: