Manual Scheppach BS3000 Primaster (page 25 of 44) (English, German, French)

782175

Zoom out

Zoom in

1/44

25GB

• Relieve the saw band tension with the clamping

screw (9), remove the band. Fig. 9

• Insert a new saw band.

Side correction (Fig. 9)

• The sawblade should run in the centre of the band

wheels.

• Turn the upper band wheel by hand in the cutting

direction, and make the side correction by means

of the handle (K).

• Attention! The saw band should run over the cen-

tre of the band wheel after multiple turns. Visual

inspection!

• Turn the band wheel by hand in the cutting direc-

tion while determining the nal tension with the ten-

sion screw (9). The degree of tensioning depends

on the sawblade width. Wide sawblades must be

tensioned more than narrow ones.

• After successful setting rmly tighten the locknut

(M). Close the guard.

Attention: Too strong a tensioning will cause prema-

ture breaking.

• Fit the guide rail for the lengthwise aligning stop in

reverse order (Fig. 7+8)

• After termination of the work, always relieve the

tension by releasing tension bolt (9).

8.7 Storing the push rod (Fig. 15)

In order to have the push rod (N) to hand at all times,

hang it on the device (i) intended for this, at the top

left side of your band saw.

8.8 Transverse cutting gauge (optional) (Fig. 16)

• Slide lateral stop (j) into a groove (k) in the saw

bench.

• Release the grip screw (l).

• Turn the lateral stop (j) until the desired angular

dimension has been set. The arrow on the lateral

stop indicates the set angle.

• Retighten the grip screw (l).

• The stop rail (n) can be slid against the lateral

stop (j). To do so, loosen the knurled screws (m)

and slide the stop rail (n) into the desired position.

Tighten the knurled screws (m) again

• Attention! Do not slide the stop rail (n) too far in the

direction of the saw blade.

8.9 On/Off switch (Fig. 1)

• To turn the machine on, press the green button

„1“ (8).

• To turn the machine off again, press the red but-

ton „0“(8).

• The band saw is equipped with an undervoltage

switch. With a power failure, the band saw must

be switched back on again.

Attention!

When working with the machine, all protective devic-

es and guards must be tted.

The upper and lower bandwheel is protected by a

xed guard and an articulated cover. When opening

the cover, the machine is switched off. Starting is

possible only with closed cover.

9. Transport

The machine must only be lifted and transported on

its frame or the frame plate. Never lift the machine at

the safety devices, the adjusting levers, or the saw-

ing table.

During the transport the saw blade protection must

be in the lowest position and near the table.

Never raise at the table!

Unplug the machine from the mains during transport.

10. Working instructions

The following recommendations are examples of the

safe use of band saws. The following safe working

methods should be seen as an aid to safety. They can-

not be applied suitably completely or comprehensively

to every use. They cannot treat every possible dan-

gerous condition and must be interpreted carefully.

• Connect the machine to a suction unit when working

in closed rooms. A suction device which conforms

with commercial regulations must be used for suc-

tion in commercial areas.

• Loosen the sawband when the machine is not in

operation (e.g. after nishing work). Attach a notice

on the tension of the saw band to the machine for

the next user.

• Collect unused sawbands and store them safely in

a dry place. Check for faults (teeth, cracks) before

use. Do not use faulty sawbands!

• Wear suitable gloves when handling sawbands.

• All protective and safety devices must be securely

mounted on the machine before beginning work.

• Never clean the sawband or the sawband guide with

a hand-held brush or scraper while the sawband is

running. Resin-covered sawbands impair working

safety and must be cleaned regularly.

• For your own protection, wear protective glasses

and hearing protection. Wear a hairnet if you have

long hair. Roll up loose sleeves over the elbows.

• Always position the sawband guide as near the

workpiece as possible when working.

• Insure sufcient lighting in the work area and

around the machine.

• Always use the fence for straight cuts to keep the

workpiece from tipping or slipping away.

• When working on narrow workpieces with manual

feed, use the push stick.

• For diagonal cuts, place the saw bench in the ap-

propriate position and guide the workpiece on the

fence.

• Insure safe workpiece guidance.

• For arced and irregular cuts, push the workpiece

evenly using both hands with the ngers together.

Hold the workpiece with your hands on a safe area.

• Use a pattern for repeated arced or irregular cuts.

• Insure that the workpiece does not roll when cut-

ting round pieces.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach BS3000 Primaster in the language / languages: English, German, French as an attachment in your email.

The manual is 3.93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach BS3000 Primaster Manual

Product: