Manual Scheppach Bestcombi 310 Kity (page 20 of 35) (English, German, French)

782109

Zoom out

Zoom in

1/35

• workpiece. Pay attention to the splitting

wedge thickness, see the numbers pun-

ched on the splitting wedge. The splitting

wedge may not be thinner than the saw

blade body and not thicker than its saw kerf

width.

• Lower the covering hood on the workpiece

during each operation

• The covering hood must be horizontal

during each operation

• During longitudinal cutting of small workpi-

eces – smaller than 120 mm - use the slide

rod without fail. The slide rod must be used

to prevent working with the hands in the

vicinity of the saw blade.

• Switch the machine off to rectify faults or to

remove jammed wood pieces. Disconnect

the power plug.

• Replace the table insert in case of lined

saw crevices. Disconnect the power

plug.

• Conversion-, adjustment-, measurement-

and cleaning jobs are to be performed only

after the motor is switched off. Disconnect

the power plug.

• Before start-up, the machine should be

connected to a vacuum cleaner with a

exible, non-inammable suction pipe.

The vacuum cleaner must get activated

automatically when the circular table saw is

switched on.

• Switch the motor off while leaving the work-

place. Disconnect the power plug.

• Even if there is a slight position change,

disconnect the machine from any external

power source. Reconnect the machine

properly to the mains power supply again

before restart.

• Only electricians should be allowed to per-

form installation, repair and maintenance

jobs on the electrical equipment.

• All protection and safety devices must be

reinstalled immediately after the repair and

maintenance jobs are over.

• Do not expose electrical tools to rain.

• Do not use electrical tools in humid and wet

environments.

• Ensure good illumination of the work area.

• Do not use electrical tools at places where

there is risk of re or explosion.

• Avoid body contact with earthed parts (e.g.,

pipes, radiators, electric stoves, cooling

devices).

• Unused electric tools should be stored at

a dry, elevated or sealed place outside the

reach of children.

• Do not pull the cable to disconnect the po-

wer plug from the mains socket. Protect the

cable from heat, oil and sharp edges.

• Use clamping devices, slide handles or a

slide rod to hold the workpiece in place.

It can be held safer this way than with the

hand.

• Keep the handles dry, clean and free of oil

and grease.

• While inserting the power plug into the

mains socket, ensure that the switch is off.

• Use only an approved and appropriately

marked extension cable in the open.

• Do not use electric tools in which the switch

cannot be activated and deactivated

• Circular saws should not be used for split-

ting (groove ending in the tool).

• Use only saw blades whose maximum

permissible speed is not less than the ma-

ximum spindle rotation speed of the circular

table saw and the material to be cut.

• When transporting the machine, use only

transportation equipment and never use

protective devices for handling or transport.

• During transportation, the topmost section

of the saw blade must be covered, e.g.,

with the protective device. Purchase acces-

sories only from your specialised dealer.

• The circuit breaker (16A) with RCD module

(30mA) and overvoltage protection devices

shall be installed for supplying electric

power to this machine, in order to protect

people against electrical shock due to in-

direct shock.If the machine is connected in

TN system, Test 2 according to EN 60204-1

is to be veried under nal installation.

Proper use according to manufacturer´s instructions m

The machine corresponds to the applicable

EC Machine Directive.

• The machine has a workplace which is

located before the machine at the left of the

machine table.

• To prevent accidents, the working- and

surrounding area of the machine must be

free of disturbing foreign bodies.

• In principle, the workpieces to be pro-

cessed must be free of foreign bodies such

as nails or screws.

• Before start-up, the machine should be

connected to a vacuum cleaner with a

exible, non-inammable suction pipe. The

grading must be activated automatically

when the circular table saw is switched

on. The ow speed at the vacuum suction

nozzle must be 20 m/s.

The activation automation is available as special

accessory.

Type ALV 2: Art. No. 7910 4010, 230 V/50 Hz

On switching the machine on, the vacuum

cleaner starts automatically after a lag of 2-3

seconds. This prevents overloading of the

internal fuse. On switching the machine off, the

vacuum cleaner is deactivated automatically

after a lag of 3-4 seconds. The residual dust is

removed this way, as required by the Hazardous

Substances Ordinance. This saves power and

reduces the noise. The vacuum cleaner runs

only when the machine is operated. For jobs in

the commercial area, a suitable and approved

dust lter must be used. Do not connect or dis-

connect vacuum cleaner or dust lter when the

machine is in operation.

• The machine is designed exclusively for

processing wood and similar substances.

Only original tools and accessories are to

be used. Depending on the section- and

wood type (solid wood, plywood or particle

boards) use the required saw blade accor-

ding to Standard EN 847-1. Observe the

tool special accessories at the end of this

operating instructions manual.

• Use the machine only if it is in a awless

condition technically, and only after lear-

ning about its proper and safe use, as well

as about the risks involved, complying with

the operating instructions! Get faults that

compromise safety in particular rectied,

immediately

• The safety-, work- and maintenance speci-

cations of the manufacturer as well as the

dimensions specied in the technical data

must also be observed.

• The appropriate accident prevention regula-

tions and the other generally acknowledged

safety rules must be observed.

• The machine is to be used, evaluated or

repaired only by persons who are familiar

with the working of the machine, and are

informed about the involved risks. Unautho-

rized changes in the machine will release

the manufacturer from any liability for the

damages resulting there from.

• The machine may be used only with original

accessories and original tools of the manu-

facturer.

• Any use going beyond this will be interpre-

ted as improper. The manufacturer will not

be liable for damages resulting there from;

the risk will be borne by the user alone.

The machine is designed on the basis of

the latest technology and the recognized

safety-related rules. Nevertheless, individual

residual risks may occur when performing

jobs on the machine.

• Risk of physical injury to ngers and hands

from the rotating tool, if the workpiece is

not guided properly.

• Risk of injury from the departing workpiece

during improper holding and guidance,

such as performing jobs without stop.

• Risk to health from noise. When working,

the permissible noise level is exceeded.

Wear personal safety equipment such as

ear guards without fail.

• Physical injuries due to defective saw

blade. Check the saw blade regularly and

before each use for physical integrity.

• Risk from power, the use of improper elec-

trical connecting cables.

• When using special accessories, the at-

tached operating instructions must be read

carefully and observed.

• Nevertheless, apparent residual risks may

occur despite taking all precautions.

• Residual risks can be minimized if the safe-

ty instructions and the “Proper use accor-

ding to manufacturer’s instructions” as well

the operating instructions are observed on

the whole.

DGB

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Bestcombi 310 Kity in the language / languages: English, German, French as an attachment in your email.

The manual is 2.55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach Bestcombi 310 Kity Manual

Product: