Manual Scheppach Basa 7.0 (page 15 of 92) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

782165

Zoom out

Zoom in

1/92

DGB

Safety notes

 In these operating instructions we have

marked the places that have to do with your

safety with this sign.

• Please pass on safety notes and instructions

to all those who work on this machine.

• Personnel entrusted with work on the machine

must have read the operating instructions

and in particular the chapter on safety before

beginning work. Reading the instructions

after work has begun, is too late. This applies

especially to persons working only occasio-

nally on the rnachine, e.g. during setting up or

rnaintenance.

• Observe all safety instructions and warnings

attached to the machine.

• See to it that all safty instructions and war-

nings attached to the machine are complete

and perfectly legible.

• Check all power supply lines. Do not use

defective lines.

• Make sure that the machine stands stable on

rm ground.

• Insure sufcient lighting in the work area and

the area around the machine.

• Caution when working: There is a danger to

ngers and hands from the rotating tool.

• When working on the machine, all safety me-

chanisms and covers must be mounted.

• Keep children away from the machine when it

is connected to the power supply.

• Operating personal must be at least 18 years

of age. Trainees must be at least 16 years of

age, but may only operate the machine under

adult supervision.

• Persons working on the machine may be not

diverted from their work.

• The working space on the machine must be

free of chips and wood scrap.

• Wear only close-tting clothes. Remove rings,

bracelets and other jewelry.

• Always wear safety goggles when working.

• Wear a cap or hair net to protect long hair.

• Wear suitable gloves to change the sawband.

• Do not wear work gloves when working on the

saw.

• Observe the correct rotational speed setting

on the machine.

• The safety mechanism on the machine may

not be removed or rendered unusable.

• Cleaning, changing, calibrating, and setting of

the machine may only be carried out when the

motor is switched off. Pull the power supply

plug and wait for the rotating tool to completely

stop.

• Connection and repair work on the electrical

installation may be carried out by a qualied

electrican only.

• All protection and safety devices must be

replaced after completing repair and mainte-

nance procedures.

• Switch the machine off and pull power supply

plug when rectifying any malfunctions.

• Use a suction unit to suck up wood shavings

and sawdust. The current speed at the suction

connection piece should be 20 m/s.

• Check the saw band guide and the saw band

tension before starting up.

• Do not use nicked saw bands or those that

have an altered form.

• Replace table inserts that have worn saw

slots.

• When sawing round wood, make sure that the

work piece does not turn.

• For sawing heavy or cumbersome pieces, use

the appropriate working aids for bracing.

(Special accessory roller stands).

• Place the upper saw band guide as closely as

possible to the work piece.

• On slanted table plates, attach the longitudinal

stop on the lower table plate half.

• Do not brake the saw band with side pressure

after switching off.

• Remove work pieces that have become stuck

only with the motor switched off and with the

saw band at a standstill.

• Cut off the external power supply of the ma-

chine even if only minor changes of place are

envisaged. Properly reconnect the machine to

the supply mains before recommissioning.

• When leaving the work place, switch the motor

off. Pull the power supply plug.

Use only as authorized

 CE tested machines meet all valid EC

machine guidelines as well as all relevant

guidelines for each machine.

• All protective and safety device must be moun-

ted on the machine before beginning work.

• The machine is designed to be operated by

one person. The operator is responsible for all

other persons in the working area.

• Observe all safety instructions and warnings

attached to the machine.

• See to it that safety instructions and warnings

attached to the machine are always complete

and perfectly legible.

• The bandsaw with the supplied tools and

accessories is designed exclusively for sawing

wood, material similar to wood, and non-

ferrous metals and steel.

• The maximum dimensions for workpieces to

be processed is may not exceed the bench

size in the standard version. Clearance width:

440 mm, Clearance height: 300 mm

• For larger workpiece dimensions which require

tipping of the table top, the table extension or

the dolly (special accessories) must be used.

• The band saw can also be used for sawing

metal when it is equipped with a special saw

band dolly (special accessory) and a operated

at an adapted cutting speed. Metal allows

with more than 80 % magnesium may not be

processed due to the danger of res.

• When used in enclosed rooms, the machine

must be connected to a vacuum exhaust unit.

Use the dust extractor to remove matchwood

or saw dust. The vacuum support ow rate

must be 20 m/s. Subatmospheric pressure

860 Pa.

• The automatic switching unit is available as a

special accessory.

Type ALV 2 Art. No. 7910 4010 230 V/50 Hz

Type ALV 10 Art. No. 7910 4020 400 V/230

V/50 Hz

• The vacuum exhaust unit automatically

switches on after a 2-3 second delay after the

machine tool is turned on. This avoids overloa

ding the circuit fuse.

• After turning off the machine tool, the vacuum

exhaust unit remains on for an additional 2-3

seconds and is then automatically switched

off. Remaining dust is thereby removed by

vacuum exhaust, as required by German

regulations governing hazardous materials.

This results in savings in electricity consump-

tion and reduces noise levels, as the vacuum

exhaust unit is on only during machine tool

operation.

• A suction device which conforms with com-

mercial regulations must be used for suction in

commercial areas.

• Do not switch off or remove suction units or

dust extractors while the work machine is in

operation.

• The machine must only be used in techni-

cally perfect condition in accordance with its

designated use and the instructions set out

in the operating manual, and only by safety-

conscious persons who are fully aware of the

risks involved in operating the machine. Any

functional disorders, especially those affecting

the safety of the machine, should therefore be

rectied immediately.

• The safety, work and maintenance instructions

of the manufacturer as well as the technical

data given in the calibrations and dimensions

must be adhered to.

• Relevant accident prevention regulations and

other, generally recognized safety-technical

rules must also be adhered to.

• The machine may only be used, maintained,

and operated by persons familiar with it and

instructed in its operation and procedures.

Arbitrary alterations to the machine release

the manufacturer from all responsibility for any

resulting damages.

• The machine may only be used with original

acces sories and original tools made by the

manufacturer.

• Any other use exceeds authorization. The ma-

nufacturer is not responsible for any damages

resulting from unauthorized use; risk is the

sole responsibility of the operator.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Basa 7.0 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5.04 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach Basa 7.0 Manual

Product: