781468

Scheppach Basa 5.0 Manual

29
Zoom out
Zoom in
Previous page
1/148
Next page
evenly using both hands with the ngers together.
Hold the workpiece with your hands on a safe
area.
• Use a pattern for repeated arced or irregular cuts.
• Insure that the workpiece does not roll when
cutting round pieces.
• Use the traverse cutting gauge special acces-
sory for safety when making traverse cuts.
• To safely cut round plates, use the circular cut-
ting unit special accessory.
Electrical Connection
The installed electric motor is connected
and is ready to work.
The connection complies with the relevant VDE
and DIN regulations.
The customer-side mains supply and the used
extension line must meet these regulations.
Installations, repair, and maintenance work
relating to the electric installation may only be
performed by specialists.
Important Notes
The electric motor has been designed for the S 1
operating mode.
In case of an overload of the motor, it turns off
automatically. After a cooling period (duration
varies), you can turn on the motor again.
Defective Electric
Connection Lines
Often, insulation damages occur on electrical
connection lines.
Causes are:
1. Drag marks if connection lines are led through
window or door clearances.
2. Kinks due to improper attachment or routing of
the connection line.
3. Cuts caused by running over the connection
line.
4. Insulation damages caused by pulling the con-
nection line out of the wall socket.
5. Fissures caused by the ageing of the insulation.
Such defective electric connection lines must
not be used and are hazardous due to the
insulation damages.
Regularly check the electrical connection lines for
damages. Please make sure that the connection
lines are disconnected from the mains supply
during the check.
Electrical connection lines must comply with the
relevant VDE and DIN regulations. Only use con-
nection lines labelled with H 07 RN. The labelling
of the connection cable with the type specication
is required.
AC motor
1. The supply voltage must be 230 V / 50 Hz.
2. Extension lines up to a length of 25 m must
have a cross section of 1.5 square millimetres.
Extension lines with a length of more than 25
m must have a minimum cross section of 2.5
square millimetres.
3. The mains connection is protected with a delay-
action fuse of 16 A.
Rotary current motor
1. The supply voltage must be 400 V / 50 Hz.
2. Mains supply and extension line must be ve-
wire = 3 P + N + SL.
3. Extension lines must have a minimum cross
section of 1.5 square millimetres.
4. The mains connection is protected with a maxi-
mum of 16 A.
5. In case of mains supply or change of location,
the direction of rotation must be checked. If
required, the polarity must be reversed.
If you have further questions, please specify
the following:
1. Motor manufacturer
2. Kind of current of the motor
3. Data from the machine type plate
4. Data from the switch type plate
If you return the motor, always return the com-
plete drive unit with the switch.
Maintenance
Carry out retting, setting measurement and
cleaning work only when the motor is switched
off. Pull the plug and wait for the sawband to
come to a full stop.
An experience worker can carry out minor-
repairs on the machine himself.
Repair and maintenance work on the electrical
system may only be carried out by a qualied
electrician.
All protective and safety devices must be re-
attached immediately after completed repair
and maintenance work.
GB
GB
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Basa 5.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Basa 5.0 in the language / languages: All languages as an attachment in your email.

The manual is 4.84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info