699394
41
Zoom out
Zoom in
Previous page
1/110
Next page
SATEL VERSA Plus 39
Timer priority – if this option is enabled, the timer always disarms the system (if the option is
disabled, the timer will only disarm the system, if it armed it).
6. Zones
A zone can be assigned to one or two partitions. If the zone is assigned to two partitions, it
can be armed when both partitions are armed or one of them only.
The system supports the following zones:
hardwired – on the control panel PCB and in expanders. The number of available
hardwired zones is determined by the control panel during the identification procedure.
wireless – after connecting the 433 MHz wireless system controller (VERSA-MCU) or the
ABAX wireless system controller (ACU-120, ACU-270, ACU-100 or ACU-250). The
number of available wireless zones depends on the number of wireless devices registered
in the system and is determined during the procedure of adding them.
virtual – zones which do not physically exist, but are controlled by means of keyfobs.
6.1 Assignment of numbers to mainboard zones
By default, the zones on mainboard have numbers from 27 to 30. These zones can be
assigned any numbers from the 1 to 30 range. You can do it in the following manner:
DLOADX program: “VERSA – Structure” window “Hardware” tab “VERSA Plus:
[system name]” branch,
keypad: SERVICE MODE 2. HARDWARE INP.Z1 NUMBER / INP.Z2 NUMBER / INP.Z3 NUMBER /
INP.Z4 NUMBER.
Assignment of number 0 to a zone means that the zone will not be used.
6.2 Programming the EOL resistor values
For the zones in zone expanders identified by the control panel as CA-64 Ei and CA-64 EPSi,
the value of end-of-line resistors is programmable within the range from 500 to 15 k.
You can define the resistor value when configuring the expander:
DLOADX program: “VERSA – Structure” window “Hardware” tab “Expansion modules”
branch [expander name],
keypad: SERVICE MODE 2. HARDWARE 1. KPDS & EXP. 2. SETTINGS [expander name].
The sum of values programmed for the resistors R1 and R2 may not be lower than
500
or higher than 15 k
.
You can program the value 0 for the resistor R2. In the 2EOL configuration you must
use then two resistors, the resistance value of each being equal to half the value
defined for the resistor R1.
In the EOL configuration, the resistance value is equal to the sum of values
programmed for the resistors R1 and R2.
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel Versa Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel Versa Plus in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel Versa Plus

Satel Versa Plus User Manual - English - 44 pages

Satel Versa Plus Installation Guide - English - 36 pages

Satel Versa Plus Quick start guide - English - 11 pages

Satel Versa Plus Installation Guide - English - 32 pages

Satel Versa Plus Quick start guide - German - 12 pages

Satel Versa Plus Additional guide - German - 113 pages

Satel Versa Plus User Manual - German - 46 pages

Satel Versa Plus Installation Guide - German - 36 pages

Satel Versa Plus Quick start guide - Dutch - 11 pages

Satel Versa Plus User Manual - Dutch - 46 pages

Satel Versa Plus Additional guide - Dutch - 110 pages

Satel Versa Plus Additional guide - Dutch - 2 pages

Satel Versa Plus Installation Guide - Dutch - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info