699394
31
Zoom out
Zoom in
Previous page
1/36
Next page
SATEL VERSA Plus 29
5.17.2 Removing ABAX wireless devices
DLOADX program
You can remove ABAX wireless devices in the “Versa – Structure” window, “Hardware” tab,
after clicking on the ABAX system controller name in the list of devices.
1. In the “Zones/Outputs” tab, click on the “Read” button to read the data related to wireless
devices from the controller.
2. Click on the zone to which the device you want to delete is assigned (if the device is
assigned to several zones, you can click on any of them).
3. Click on the “Delete” button. The “Confirm” window will open.
4. Click on the “Yes” button. The “Confirm” window will close.
5. Click on the “Write” button to save the changes to the controller.
LCD keypad
You can remove ABAX wireless devices in the service mode by means of the REMOVE DEVICE
function (SERVICE MODE 2. HARDWARE 1. KPDS. & EXPS. 3. WIRELESS MOD. 3. REMOVE
DEVICE
).
1. Having started the function, use the
and keys to select the zone to which the
wireless device to be removed is assigned, and then press .
2. A prompt will appear asking you whether the device is to be deleted (device type and
serial number will be displayed). Press . The device will be deleted.
5.18 Installation of 433 MHz wireless detectors
If the 433 MHz wireless system controller (VERSA-MCU) is connected to the control panel,
you can proceed to installation of the 433 MHz wireless detectors after control panel start-up
and controller identification by the control panel. Before installation of the detector, register it
in the controller and check, if transmissions from the detector located at the planned
installation place can reach the controller. To send a transmission, you can e.g. open the
detector tamper switch. If transmissions from the detector planned installation place do not
reach the controller, select another location. Sometimes, it is sufficient to move the detector
by some ten to twenty centimeters. Only after making sure that the controller receives
transmissions from the detector, you can install the detector permanently.
The wireless detectors must be registered to the alarm system. This can be done using the
DLOADX program or LCD keypad.
5.18.1 Adding new 433 MHz wireless detectors
The control panel can support up to 30 wireless detectors.
DLOADX program
You can add 433 MHz wireless detectors in the “Versa – Structure” window, “Hardware” tab,
after clicking on the VERSA-MCU controller name in the list of devices.
1. Click on the “Read” button to read the data related to wireless detectors from the
controller (these data are not read after clicking on the button in the main menu).
2. Click on the zone to which a new wireless detector is to be assigned (you can also select
the zone later in the “New wireless dev.” window).
3. Click on the “New device” button. The “New wireless dev.” window will open.
4. Enter the 7-digit serial number of the added detector. The serial number can be found on
the electronics board or on the enclosure.
5. Open the detector tamper contact.
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel Versa Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel Versa Plus in the language / languages: English as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel Versa Plus

Satel Versa Plus User Manual - English - 44 pages

Satel Versa Plus Additional guide - English - 110 pages

Satel Versa Plus Quick start guide - English - 11 pages

Satel Versa Plus Installation Guide - English - 32 pages

Satel Versa Plus Quick start guide - German - 12 pages

Satel Versa Plus Additional guide - German - 113 pages

Satel Versa Plus User Manual - German - 46 pages

Satel Versa Plus Installation Guide - German - 36 pages

Satel Versa Plus Quick start guide - Dutch - 11 pages

Satel Versa Plus User Manual - Dutch - 46 pages

Satel Versa Plus Additional guide - Dutch - 110 pages

Satel Versa Plus Additional guide - Dutch - 2 pages

Satel Versa Plus Installation Guide - Dutch - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info