699394
29
Zoom out
Zoom in
Previous page
1/36
Next page
SATEL VERSA Plus 27
5.16 Connecting the computer to the control panel
Using a computer, you can configure the alarm system / voice module (DLOADX program /
VG-SOFT) or update the control panel firmware. The communication is encrypted. The
computer can be connected to the control panel through a USB port. After connecting the
control panel to the computer, the Windows system will automatically detect that a new
device is connected and will install system drivers for the HID interface device.
5.17 Installation of ABAX wireless devices
This section does not cover installation of the wireless keypads. They constitute
a separate category of devices and should be installed according to the manual
delivered with the device.
If an ABAX wireless system controller (ACU-120 / ACU-270 / ACU-100 / ACU-250) is
connected to the control panel, you can proceed to installation of ABAX wireless devices
after control panel start-up and controller identification by the control panel. Before installing
a wireless device, check the level of radio signal received by the device from controller and
by the controller from device at the planned installation place. The ARF-100 tester is a useful
tool to check the signal level. The level of signal received by device/controller may not be
lower than 40%. If the radio signal level at the planned installation place is too low, select
another installation location. Sometimes it is sufficient to move the device ten or twenty
centimeters to obtain a significant improvement of signal quality. You can install the device
permanently only after reaching the optimum level of radio signal.
The wireless devices must be registered to the alarm system. This can be done using the
DLOADX program or LCD keypad.
5.17.1 Adding new ABAX wireless devices
The control panel can support up to 30 wireless devices. The number of actually supported
devices depends on how many positions the individual devices occupy. Each position means
one wireless zone or one wireless zone and one wireless output.
If a device occupies two or more positions, its addition will respectively decrease the number
of wireless devices that can still be registered (e.g. after adding a ACX-200 expander, which
takes up 4 positions, the controller can still support 26 other wireless devices).
Even if a device occupies several zones in the system, only the first of them should be
indicated during the device adding procedure. The next ones are assigned automatically
(these are the zones following the selected one).
For some wireless devices, you can select whether the device will take up one or two
positions (channels) on the list of devices. Depending on the device, if one position is
selected:
AMD-101 – only additional NC input will be supported,
AMD-102 – only additional inputs (roller shutter and NC) will be supported;
AOD-200 – only the motion detector will be supported;
AVD-100 – only the vibration detector will be supported.
If the device occupies an output as well, its number will be the same as the number of zone
selected during the device adding procedure.
The control panel does not support wireless outputs with numbers from 13 to 30.
DLOADX p
rogram
You can add ABAX wireless devices in the “Versa – Structure” window, “Hardware” tab, after
clicking on the ABAX system controller name in the list of devices.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel Versa Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel Versa Plus in the language / languages: English as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel Versa Plus

Satel Versa Plus User Manual - English - 44 pages

Satel Versa Plus Additional guide - English - 110 pages

Satel Versa Plus Quick start guide - English - 11 pages

Satel Versa Plus Installation Guide - English - 32 pages

Satel Versa Plus Quick start guide - German - 12 pages

Satel Versa Plus Additional guide - German - 113 pages

Satel Versa Plus User Manual - German - 46 pages

Satel Versa Plus Installation Guide - German - 36 pages

Satel Versa Plus Quick start guide - Dutch - 11 pages

Satel Versa Plus User Manual - Dutch - 46 pages

Satel Versa Plus Additional guide - Dutch - 110 pages

Satel Versa Plus Additional guide - Dutch - 2 pages

Satel Versa Plus Installation Guide - Dutch - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info