629722
72
Zoom out
Zoom in
Previous page
1/93
Next page
70 VERSA IP SATEL
11.2.1 Options
Station 1 or 2 – select this option if the control panel is to send event codes to Station 1, and
in the case of failure – to Station 2.
Station 1 – select this option if the control panel is to send event codes to Station 1 only.
Station 2 – select this option if the control panel is to send event codes to Station 2 only.
Station 1 and 2 – select this option if the control panel is to send event codes to both
monitoring stations.
Events amount limiting – if the option is enabled, events from the same source are saved
into the event log and reported to the monitoring station 3 times only. This option does not
apply to the alarms from zones (see: A
UTO-RESET 3 or AUTO-RESET 1 zone option).
Report module restarts – if the option is enabled, in case of sending event codes in Contact
ID or SIA format, the monitoring station is informed about module restarts.
Restore after bell – if the option is enabled, the zone restore code will only be sent to the
monitoring station after the alarm signaling ends. If a few outputs are signaling alarm, the
zone restore code will be sent when one of them stops signaling the alarm.
Restore after disarm – if the option is enabled, the zone restore code will only be sent to the
monitoring station after disarming the partition to which the zone belongs.
11.2.2 Station 1 / Station 2
Reporting format – format in which event codes are sent to the monitoring station.
In the TELIM format, events can only be sent via the analog telephone line.
Telephone
Telephone no. – telephone number of the monitoring station.
Repetitions the number of attempts to send an event code via the telephone line. If all
attempts fail, the control panel will suspend reporting via the telephone line. Up to 31
retries can be programmed. Programming the value 0 means that monitoring will be
suspended after 8 attempts.
Suspend time – the time for which reporting will be suspended, if attempts fail to send an
event code through all provided transmission paths. The control panel will resume the
attempt of establishing telephone connection with the monitoring station after this time
expires or a next, new event occurs. Up to 30 minutes can be programmed. Programming
the value 0 means that an attempt to establish telephone connection with the monitoring
station will only be taken after occurrence of a new event in the system.
ETHM
Server address – network address of the monitoring station for reporting via Ethernet. You
can enter either the IP address or the domain name.
Port – number of port used for communication between the control panel and the monitoring
station. You can enter a value from 1 to 65535.
Station key – a string of up to 12 alphanumeric characters (digits, letters and special
characters), which is used for encryption of data sent to the monitoring station.
ETHM key – a string of up to 5 alphanumeric characters to be used for identification of the
control panel for the purposes of reporting via Ethernet.
Identifiers
Event codes are sent to the monitoring station with one of the four identifiers:
identifier 1 – events from zones (alarms, tampers, troubles),
72


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel Versa IP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel Versa IP in the language / languages: English as an attachment in your email.

The manual is 1,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel Versa IP

Satel Versa IP Quick start guide - English - 11 pages

Satel Versa IP User Manual - English - 32 pages

Satel Versa IP Installation Guide - English - 36 pages

Satel Versa IP User Manual - English - 43 pages

Satel Versa IP Quick start guide - German - 11 pages

Satel Versa IP Additional guide - German - 97 pages

Satel Versa IP User Manual - German - 45 pages

Satel Versa IP Installation Guide - German - 38 pages

Satel Versa IP Quick start guide - Dutch - 2 pages

Satel Versa IP User Manual - Dutch - 45 pages

Satel Versa IP Quick start guide - Dutch - 12 pages

Satel Versa IP Additional guide - Dutch - 93 pages

Satel Versa IP User Manual - Dutch - 45 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info