699901
2
Zoom out
Zoom in
Previous page
1/8
Next page
2 RE-4K SATEL
flashing red – transmission has been received from keyfob with low battery.
tamper switch.
antenna.
MODE1, MODE2, MODE3 and MODE4 pins. To be used for setting the operating mode
of relay outputs. The digit stands for the number of the relay output.
PRG1, PRG2, PRG3 and PRG4 buttons. Allow you to enroll keyfobs and define the cut-
off time of relay outputs. The digit stands for the number of the control channel / relay
output. The PRG4 button can be used to start communication with the DLOAD10
program. The PRG1 button can be used to restore the factory default settings.
Terminals
TMP - NC type tamper output (opening the tamper switch opens the output). You can
connect the TMP output to the appropriately programmed output of the alarm
control panel.
AR - input supervising the armed status in the alarm system. The input is activated
after applying the common ground. Connect the AR input to the control panel
OC type output programmed as “Armed status”.
AL - input supervising the alarm status in the alarm system. The input is activated
after applying the common ground. Connect the AL input to the control panel
OC type output indicating the alarm to be cleared.
LV - output indicating low battery in the keyfob. The output will be turned on after
receiving a transmission from the keyfob with low battery. The output will be
turned off after receiving a transmission from the keyfob whose battery is OK.
OC type output (shorted to common ground when active). You can connect
e.g. a LED to the LV output, or you can connect the output to an appropriately
programmed zone of the alarm control panel.
SS - output indicating arming / disarming / alarm clearing in the alarm system. The
indication will be triggered if the AR and/or AL input status is changed within
4 seconds of receiving a transmission from the keyfob. The indication is
provided in the form of pulses of 0.16 second duration:
1 pulse – arming,
2 pulses – disarming,
4 pulses – disarming and/or alarm clearing.
OC type output (shorted to common ground when active). You can connect
e.g. a siren to the SS output.
+12V - power input (9...16 V DC).
COM - common ground.
C1...C4 - relay output common contact.
NC1...NC4 - relay output normally closed contact.
NO1...NO4 - relay output normally open contact.
3. Keyfobs
The controller supports the following SATEL 433 MHz keyfobs:
MPT-300 – 5-button keyfob,
T-4 – 4-button keyfob,
T-2 – 2-button keyfob,
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel RE-4K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel RE-4K in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel RE-4K

Satel RE-4K User Manual - German - 11 pages

Satel RE-4K User Manual - Dutch - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info