699526
18
Zoom out
Zoom in
Previous page
1/27
Next page
16 PERFECTA SATEL
Do not connect two devices with power supply to one-section transformer.
Before connecting transformer to a circuit from which it will be powered, make
sure the circuit is de-energized.
6.9.2 Backup power supply
A 12 V lead-acid sealed battery should be connected to the control panel as a backup power
source. The battery capacity must be adequately selected to match current consumption in
the system. According to EN 50131 Grade 2, the battery must ensure operation of the system
without mains supply for 12 hours.
If the battery voltage drops below 11 V for longer than 12 minutes (3 battery tests), the
control panel will indicate battery failure. When the voltage goes down to approx. 10.5 V, the
battery will be disconnected.
Do not connect deeply discharged battery to the control panel (with voltage
across unloaded terminals below 11 V). The battery should be precharged with
a proper charger.
The used batteries must not be discarded, but should be disposed of in
accordance with the existing rules for environment protection.
6.9.3 Control panel power-up / start-up procedure
1. De-energize the 230 V AC circuit to which the transformer is to be connected.
2. Connect the 230 V AC wires to the terminals of transformer primary winding.
3. Connect the terminals of transformer secondary winding to the control panel AC
terminals. To make the connection, use flexible conductors with a cross-section of 0.5 –
0.75 mm
2
, or rigid conductors with a cross-section of 1 – 2.5 mm
2
.
4. Connect the battery to the dedicated leads (positive terminal to RED lead, negative
terminal to BLACK lead). If the battery has screw-type cable lugs, use adapters delivered
with the control panel (do not cut off the battery cable lugs). The control panel will not
start after connecting the battery alone.
5. Turn on 230 V AC power supply in the circuit to which the transformer is connected.
The control panel will start operating.
The above mentioned power-up sequence (first the battery, then the 230 V AC mains)
will ensure proper operation of the power supply unit and the electronic protection
circuits, thus preventing damage to the alarm system components caused by
installation mistakes, if any.
If it is necessary to de-energize the control panel, turn off the main power supply (AC)
first, and the backup power supply (battery) afterwards. Observe the above described
procedure when reconnecting the power supply.
6.9.4 Starting the service mode
If, after starting the alarm control panel, you want to perform any operations that not require
power-off (e.g. to adjust sensitivity in wired detectors), enter the service mode.
When the control panel is running in service mode, tamper alarms are not
generated.
1. Enter the service code (by default: 12345) and press .
2. User menu appears.
3. Press .
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel PERFECTA 32-WRL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel PERFECTA 32-WRL in the language / languages: English as an attachment in your email.

The manual is 0,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel PERFECTA 32-WRL

Satel PERFECTA 32-WRL Quick start guide - English - 10 pages

Satel PERFECTA 32-WRL User Manual - English - 31 pages

Satel PERFECTA 32-WRL Additional guide - English - 49 pages

Satel PERFECTA 32-WRL Additional guide - English - 50 pages

Satel PERFECTA 32-WRL Quick start guide - German - 11 pages

Satel PERFECTA 32-WRL User Manual - German - 32 pages

Satel PERFECTA 32-WRL Additional guide - German - 52 pages

Satel PERFECTA 32-WRL Additional guide - German - 50 pages

Satel PERFECTA 32-WRL Installation Guide - German - 28 pages

Satel PERFECTA 32-WRL Quick start guide - Dutch - 11 pages

Satel PERFECTA 32-WRL User Manual - Dutch - 32 pages

Satel PERFECTA 32-WRL Additional guide - Dutch - 52 pages

Satel PERFECTA 32-WRL Additional guide - Dutch - 50 pages

Satel PERFECTA 32-WRL Installation Guide - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info