699062
26
Zoom out
Zoom in
Previous page
1/37
Next page
24 Installer Manual SATEL
and telephone version. If the signal level is equal to 0, GSM/GPRS communication is
impossible. The signal level may be equal to 0 in the following cases:
antenna not connected or incorrectly connected,
telephone does not start up properly (e.g. no SIM card, invalid PIN code, blocked SIM
card)in such a case, the control panel should report trouble,
GSM network out of range.
5.13 Installation of wireless devices
Having started the control panel, you can proceed to installation of the ABAX 2 / ABAX
wireless devices. Antenna for communication with the wireless devices must be connected to
the control panel.
Before installing a wireless device, check the level of radio signal received by the device from
control panel and by the control panel from device at the planned installation place. The
ARF-200 / ARF-100 tester is a useful tool to check the signal level. The level of signal
received by device/control panel may not be lower than 40%. If the radio signal level at the
planned installation place is too low, select another installation location. Sometimes it is
sufficient to move the device ten or twenty centimeters to obtain a significant improvement of
signal quality. You can install the device permanently only after reaching the optimum level of
radio signal.
The wireless devices must be registered to the alarm system. This can be done using the
LCD keypad or DLOADX program. The control panel can support up to 48 wireless devices,
but some devices take up more than one position on the list. For example, after adding to the
system the ACX-200 expander, which takes up 4 positions on the list of devices, the control
panel will still be able to handle 44 more wireless devices. The number of positions on the list
is at the same time the number of zones and, in case of some devices, also outputs which
will be taken by the device in the system.
When adding and removing the wireless devices, remember that the identification function
registers zones and outputs by groups of 8. Already after adding one wireless device which
takes up 1 zone, the control panel will reserve 8 zones in the system for wireless devices.
The LCD keypad makes it possible to select the zone to which that device will be assigned.
Observe continuity, i.e. avoid leaving any gaps in the list, which will later reduce the number
of available zones in the system. Remember to preserve continuity also when removing
wireless devices. For example, if the devices registered in the control panel occupy 9
positions on the list, then 16 zones (2x8) are reserved in the system. After removal of the
device which occupied position 7 on the list, there will still be 16 zones (2x8) reserved in the
system for wireless devices, although 8 positions are actually taken up on the list of wireless
devices (see: Table 4). In such a case, it is recommended that the last devices be removed
from the list and then added to the system again, so as to fill up the gap in the list and reduce
the number of zones reserved for wireless devices.
In case of devices which, in addition to zones, also take up outputs, it is recommended that
you add them to the system first. This will allow you to maintain the continuity of use of not
the zones alone, but the outputs as well. Table 4 shows a situation in which the siren first
output occupies position 8, and the second output position 9. As a result, 16 outputs have
been reserved for wireless devices in the system, though actually 2 outputs are used (the
eighth output in the first group of 8 outputs and the first output in the second group of 8
outputs).
In some cases, the gaps in the list of zones/outputs cannot be avoided. It applies to situation
when the number of zones/outputs, which is used by the devices, is not a multiple of 8.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel integra 128-WRL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel integra 128-WRL in the language / languages: English as an attachment in your email.

The manual is 0,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel integra 128-WRL

Satel integra 128-WRL User Manual - English - 51 pages

Satel integra 128-WRL Additional guide - English - 114 pages

Satel integra 128-WRL Installation Guide - German - 2 pages

Satel integra 128-WRL Additional guide - German - 121 pages

Satel integra 128-WRL User Manual - German - 38 pages

Satel integra 128-WRL Additional guide - Dutch - 121 pages

Satel integra 128-WRL User Manual - Dutch - 52 pages

Satel integra 128-WRL Quick start guide - Dutch - 24 pages

Satel integra 128-WRL Installation Guide - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info