52 Parametrierung SATEL
Ausgangszeit – bezieht sich auf die Linien vom Typ 89. AUSGANGSZEIT BEENDET.
Gruppe der Ausgänge – bezieht sich auf die Linien vom Typ 92. GR. DER AUSGÄNGE AUS.
Linientyp – muss an den Meldertyp und die Methode seines Anschlusses an die Meldelinie
angepasst werden:
0. kein Melder – kein Melder ist an den Eingang angeschlossen;
1. NC – Meldelinie bedient einen Melder vom Typ NC (normal geschlossen);
2. NO – Meldelinie bedient einen Melder vom Typ NO (normal geöffnet);
3. EOL – Meldelinie bedient den Melder NO oder NC mit einem Abschlusswiderstand
im Stromkreis;
4. 2EOL/NC – Meldelinie bedient den Melder NC mit 2 Abschlusswiderständen
im Stromkreis;
5. 2EOL/NO – Meldelinie bedient den Melder NO mit 2 Abschlusswiderständen
im Stromkreis;
6. Rollladen – Meldelinie bedient den Rollladenmelder;
7. Vibration – Meldelinie bedient den Erschütterungsmelder (auch einen Melder NC);
8. Nach Ausgang – die Meldelinie bedient keine Melder – ihr Zustand hängt
ausschließlich vom Zustand des ausgewählten Ausgangs ab (physische Verletzungen
und Sabotagen der Meldelinie werden ignoriert);
9. Rollladen 2EOL – Meldelinie bedient den Rollladenmelder mit
2 Abschlusswiderständen im Stromkreis;
10. Vibration 2EOL – Meldelinie bedient den Erschütterungsmelder (auch einen Melder
NC) mit 2 Abschlusswiderständen im Stromkreis;
11. 3EOL/NC – Meldelinie bedient den Melder NC mit 3 Abschlusswiderständen
im Stromkreis;
12. 3EOL/NO – Meldelinie bedient den Melder NO mit 3 Abschlusswiderständen
im Stromkreis.
Sensibilität – je nach dem Typ der Meldelinie:
NO, NC, EOL, 2EOL/NC, 2EOL/NO, 3EOL/NC und 3EOL/NO – Zeit, während
der die Meldelinie verletzt werden soll, damit es von der Zentrale registriert wird.
Rollladen / Rollladen 2EOL – es sind 2 Parameter einzustellen (im Programm DLOADX
sind zwei Zahlen im Feld SENSIBILITÄT einzutragen):
Gültigkeitszeit des Impulses – Zeit, während der die definierte Anzahl von Impulsen
(IMPULSZAHL) auftreten soll, damit die Linie verletzt werden kann. Sie können eine 0
eintragen (Impulszähler wird nur bei Scharf-/Unscharfschltung gelöscht), 1 (30
Sekunden), 2 (120 Sekunden) oder 3 (240 Sekunden).
Impulszahl – Anzahl der Impulse, nach denen die Linie verletzt wird. Die Werte von 1
bis 8 sind einzustellen.
Vibration / Vibration 2EOL – es sind 2 Parameter einzustellen (im Programm DLOADX
werden zwei Zahlen im Feld SENSIBILITÄT einzutragen):
Sensibilität – das Auftreten des Impulses, der länger dauert, als die definierte Zeit,
bewirkt die Linienverletzung. Die Werte von 3 ms bis 96 ms (alle 3 ms) sind
einzustellen.
Impulszahl – Anzahl der Impulse, nach denen die Linie verletzt wird. Die Werte von 0
bis 7 sind einzustellen. Bei der Einstellung des Wertes 0 werden die Impulse nicht
gezählt – es wird nur die SENSIBILITÄT in Betracht gezogen.