699072
68
Zoom out
Zoom in
Previous page
1/102
Next page
66 Programming SATEL
Partitions for the 11. CHIME type output, you can indicate the partitions from which the user
will be able to block the output using the OUTPUTS CHIME function.
5.7 120. Thermostat output parameters
Temperature detector indicate the zones to which the wireless temperature detectors or
ABAX 2 wireless devices provided with a temperature sensor are assigned.
Temperature T1 the first temperature threshold. It is active when all control timers are OFF
or the forcing output is active. If the temperature threshold is active, the output will be
turned on if the temperature drops below the threshold.
Temperature T2 the second temperature threshold. It is active when the control timer is
ON or the forcing output is inactive. If the temperature threshold is active, the output will be
turned on if the temperature drops below the threshold.
Hysteresis temperature difference between turning the output on and off. The output will
be turned on when temperature drops below the threshold by a value higher than the
hysteresis. The output will be turned off when temperature rises above the threshold.
Hysteresis is used to eliminate the undesirable output state changes when temperature
fluctuations occur. Programming “0” means that hysteresis is equal to 0.5°C.
The user can edit the temperature thresholds and hysteresis using the TEMPERATURES
user function available in the CHANGE OPTIONS submenu.
Output forcing T1you can indicate the output which will force the first temperature
threshold. If the output is active, the first temperature threshold will be active. When the
output is inactive, the control timers will decide which temperature threshold is active.
The output 256 cannot be indicated as the forcing one.
Timers controlling T1/T2 you can indicate the timers which will control the temperature
threshold. When the control timer is ON, the second temperature threshold will be active
(unless the forcing output is active).
The user can edit the parameters of control timers using the TIMERS user function
available in the CHANGE OPTIONS submenu.
5.8 Output groups
The outputs of MONO SWITCH, BI SWITCH, REMOTE SWITCH, SHUTTER UP and SHUTTER DOWN
type can be grouped by the function performed by them. Each group may be given a name.
The output groups can be defined:
using the keypad, in the service mode, by means of the OUTPUT GROUPS function,
using the DLOADX program, in the “Output groups” window (to open the window, press
the “Output groups” button in the “Outputs” window).
If all outputs are assigned to one group of outputs, the keypad will not display the list
of output groups upon starting the REMOTE CONTROL user function, but it will
immediately display the list of outputs which can be controlled.
The output can be assigned to a few groups.
If the output is not assigned to any group, it cannot be controlled from the keypad.
68


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel Integra 128 Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel Integra 128 Plus in the language / languages: English as an attachment in your email.

The manual is 1,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel Integra 128 Plus

Satel Integra 128 Plus User Manual - English - 51 pages

Satel Integra 128 Plus Installation Guide - English - 35 pages

Satel Integra 128 Plus User Manual - German - 55 pages

Satel Integra 128 Plus Additional guide - German - 108 pages

Satel Integra 128 Plus Installation Guide - German - 36 pages

Satel Integra 128 Plus User Manual - Dutch - 53 pages

Satel Integra 128 Plus Additional guide - Dutch - 108 pages

Satel Integra 128 Plus Installation Guide - Dutch - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info