699331
10
Zoom out
Zoom in
Previous page
1/40
Next page
8 INT-TSI SATEL
6.2.2 Programming address without entering the service mode
This method is useful when due to repeating addresses the keypad support has been
disabled and entering the service mode is impossible.
1. Turn off keypad power supply.
2. Disconnect wires from the keypad CKM and DTM terminals.
3. Short the keypad CKM and DTM terminals.
4. Turn on keypad power supply. A window will be displayed where you can set the address.
5. Using the and keys, set the address and then tap the icon.
6. Turn off keypad power supply.
7. Open the keypad CKM and DTM terminals.
8. Connect wires, as required, to the keypad CKM and DTM terminals.
9. Turn on keypad power supply.
6.3 Keypad identification
The alarm system can only be programmed and operated from keypads that have been
identified by the control panel. The keypad identification function should be executed at the
first start-up of the control panel, and then each time when adding a new keypad or changing
address in a keypad supported by the control panel. Disconnecting an identified keypad from
the bus will trigger the tamper alarm.
The identification function can be run by using:
the keypad (SERVICE MODE STRUCTURE HARDWARE IDENTIFICATION LCD KEYPADS
ID
.);
DLOADX program (Structure” window Hardware” tab Keypads” item Keypads
identification” button).
The procedure of entering the service mode by means of the INT-TSI keypad is described in
section Programming keypad address by means of service function” (p. 7).
7. Installation of the keypad working in SLAVE mode
7.1 Installation and hook-up
Follow the procedure set forth in section describing installation and hookup of the keypad
working in MASTER mode (p. 4), but skip the steps 8 and 9 (connecting to the keypad bus of
the control panel and connecting detectors to the keypad zones).
7.2 Activating the SLAVE operating mode
1. Turn off keypad power supply.
2. Short the keypad CKM and DTM terminals.
3. Turn on keypad power supply. The Keypad configurationwindow will be displayed.
4. Tap Network” item. The network settings will be displayed.
5. Select the Slaveoption (see Fig. 6).
6. Indicate the keypad working in MASTER mode by means of which communication with
the control panel is to take place. You can do this in two ways:
tap IP address of the master keypadand use the keyboard that will be displayed to
enter the IP address of that keypad,
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel INT-TSI-BSB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel INT-TSI-BSB in the language / languages: English as an attachment in your email.

The manual is 2,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel INT-TSI-BSB

Satel INT-TSI-BSB Installation Guide - German - 34 pages

Satel INT-TSI-BSB User Manual - German - 20 pages

Satel INT-TSI-BSB Installation Guide - Dutch - 33 pages

Satel INT-TSI-BSB User Manual - Dutch - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info