699393
22
Zoom out
Zoom in
Previous page
1/28
Next page
20 INT-TSG SATEL
programmed for the R1 resistor (the value of one resistor must not be less than 500
). By
default, the following values are programmed:
R1 = 1,1 k
;
R2 = 1,1 k
.
The resistor value for Single EOL configuration is the sum of R1 and R2 resistors.
INTEGRA Plus
: parameters of the EOL resistors should be defined for the mainboard zones.
The same parameters will be set automatically for the zones in keypads in which the value
of EOL resistors is programmable. Therefore, the “EOL resistance value” tab is not
available.
7.2 Keypad connected to VERSA / VERSA Plus control panel
To configure the keypad settings, you can use:
D
LOAD
X program:
“Versa – Structure” window
“Hardware” tab
“Expanders” branch
[keypad name]
. The D
LOAD
X program alone makes it possible to configure all the
settings.
keypad:
S
ERVICE MODE
2. H
ARDWARE
1. K
PDS
.
&
EXPS
.
2. S
ETTINGS
[keypad
name].
How to enter the service mode, refer to the section on programming the keypad
address by means of the service function (p. 5).
7.2.1 Parameters and options
Shown in square brackets are the names displayed on keypads.
Name
– individual name of the keypad (up to 16 characters).
Tamper signaled in part.
[Tamper in p.] – partition where alarm will be triggered in the event
of keypad tamper (opening the enclosure or disconnecting the keypad from the bus).
CHIME signal of zones
[Zone chime] – the keypad can audibly signal violation of selected
zones. If the zone is armed, violation will not trigger the CHIME signal.
Date/Time format
– the way how date and time will be presented on the display.
Options
Sign. entry delay
[Entry time sign.] – if this option is enabled, the keypad will audibly signal
the entry delay countdown.
Sign. exit delay
[Exit time sign.] – if this option is enabled, the keypad will audibly signal the
exit delay countdown.
Sign. alarms
[Alarm signalling] – if this option is enabled, the keypad will signal the alarms
audibly.
Quick arming – Partition 1
[Part.1 QuickArm] – if this option is enabled, partition 1 can be
armed without entering the code.
Quick arming – Partition 2
[Part.2 QuickArm] – if this option is enabled, partition 2 can be
armed without entering the code.
Keys sound
– with this option enabled, pressing the keypad keys is confirmed by beeps.
Sign. trbl in part. arm
[Trbl.in part.arm] – if this option is enabled, the LED goes off after
both partitions are fully armed (if the option is disabled, the LED goes off after just one of
the partitions is armed in any mode).
Show code entering
[Code entry ind.] – if this option is enabled, entering the code is
presented on the keypad display by asterisks.
Chime on/off
– if this option is enabled, the chime signal can be turned on/off after tapping
and holding for 3 seconds
on terminal.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel INT-TSG-BSB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel INT-TSG-BSB in the language / languages: English as an attachment in your email.

The manual is 0,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel INT-TSG-BSB

Satel INT-TSG-BSB Quick start guide - English - 2 pages

Satel INT-TSG-BSB User Manual - English - 20 pages

Satel INT-TSG-BSB User Manual - English - 18 pages

Satel INT-TSG-BSB Quick start guide - German - 2 pages

Satel INT-TSG-BSB User Manual - German - 19 pages

Satel INT-TSG-BSB Installation Guide - German - 29 pages

Satel INT-TSG-BSB Quick start guide - Dutch - 2 pages

Satel INT-TSG-BSB User Manual - Dutch - 18 pages

Satel INT-TSG-BSB User Manual - Dutch - 20 pages

Satel INT-TSG-BSB Installation Guide - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info