699578
34
Zoom out
Zoom in
Previous page
1/40
Next page
32 Programming CA-6
The programming consists in entering six two-character codes which are suitable for the
given paging system.
The particular systems should be programmed as follows:
POLPAGER - [118]# [3B]#[42]#[0B]#[0F]#[01]#[7D]#
TELEPAGE - [118]# [2B]#[2E]#[0E]#[14]#[30]#[3A]#
EASYCALL - [118]# [37]#[3D]#[07]#[0B]#[B6]#[C8]#
METROBEEP - [118]# [16]#[1A]#[13]#[17]#[0B]#[0F]#
FS123 - counter count-up times (DEC)
The function makes it possible to program time intervals related to the counters 1, 2 and 3
of counting zones. The alarm will be generated only if the number of violations preset in
FS7 function takes place within the time interval defined by this function. The count-up
times may be programmed within the interval from 1 to 255 seconds (by default set at 30
seconds). If the number of violations programmed in the FS7function does not take place
within the time interval defined in the function, after expiry of the time the counting zones
counters will be reset.
After starting the function, you should enter one, two or three digits for the first counter.
Upon confirmation with the key [#], the control panel proceeds to programming the count-
up time of the next counter. In the course of programming, the AB, AB LEDs indicate (in
binary format) the counter number. On the LEDs 1-8, the control panel displays the
previously programmed setting of the parameter in the binary format (the introduced
changes will be only displayed after the function is reentered). The programming can be
terminated by pressing the [
*
] key.
EXAMPLE:
changing the counter count-up time: the first one – 60 seconds, the second – 150
seconds, the third – 255 seconds,
[12345] [#] - enter the service mode
[1][2][3] [#] - call the function
[6][0] - enter the first counter time (B LED is blinking during programming)
[#] - confirm the counter 1 count-up time and proceed to programming counter 2
[1][5][0] - enter the second counter time (A LED is blinking during programming)
[#] - confirm the counter 2 count-up time and proceed to programming counter 3
[2][5][5] - enter the third counter time (A & B LEDs are blinking during programming)
[#] - confirm the counter 3 count-up time and quit the function
FS124 - automatic readout of keypad address
The function enables the keypad address to be automatically read without changing the
other parameters.
FS125 - programming CTL input functions (HEX)
The CTL control input of the CA-6 panel can perform one of the following functions:
0 – not used,
1 - arming,
2 - disarming,
3 - FIRE alarm,
4 - PANIC alarm,
5 - alarm AUX,
6 - arming / disarming,
7 - alarm cancelling (no disarming).
Two digits are programmed. The first of them defines the input function (from 1 to 7), the
second defines which partition should be armed, disarmed or in which partition should be
cleared an alarm.
0 - for functions: FIRE alarm, PANIC alarm, alarm AUX,
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-6 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-6

Satel CA-6 Quick start guide - English - 8 pages

Satel CA-6 Installation Guide - English - 36 pages

Satel CA-6 Additional guide - German - 19 pages

Satel CA-6 User Manual - German - 19 pages

Satel CA-6 Installation Guide - German - 80 pages

Satel CA-6 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info