699607
20
Zoom out
Zoom in
Previous page
1/24
Next page
U
SER
M
ANUAL
CA-5
18
6.9 BI
OUTPUTS
[CODE][
*
][8][#]
The purpose of the function is determined by the installer. It can be used, for example, for
switching on the external lighting or any electrical devices.
The function is active when the BI
SWITCH
type is selected for one of the outputs.
Using the function will permanently change the output status into the opposite one (until the
function is used again). An inactive output will be activated, and an active output will be
deactivated.
Switching the output on is confirmed by the keypad with four short beeps and a long one,
while switching it off – with three short beeps.
6.10 P
OWER
S
UPPLY
R
ESET
[CODE][
*
][9][#]
The function is used for handling special detectors equipped with individual on/off memory,
which is cleared by shutting down power supply (for example, smoke detectors). Calling the
function temporarily disconnects power supply for such detectors.
The function is active when the RESETTABLE
POWER
type is selected for one of the outputs.
6.11 E
VENTS
[
FUNCTION
10
ONLY
LCD
KEYPAD
]
The function is available in LCD keypad and makes it possible to view the whole contents of
the events log (the last 255). To view the events, the user function menu should be opened
with master user code or with service code, and next the “Events” function should be called.
The way of viewing is described in section HOLD DOWN USER FUNCTIONS.
6.12 T
ESTING OUTPUTS AND LED INDICATORS
[CODE][
*
][11][#]
The function makes it possible to check the current status of the control panel outputs
(active/inactive), as well as functioning of the outputs and devices connected to them. After
calling the function from the LED type keypad, the control panel will indicate the current
status of outputs on LEDs with corresponding numbers: 1 – OUT1, 2 – OUT2, 3 – OUT3. The
lit up LED means active output, the extinguished LED inactive output. In the LCD keypad, the
status of outputs is displayed on the first three characters of the second line of the display.
The active outputs are indicated by displaying a corresponding digit (1, 2, or 3), and the
inactive – by displaying a dot. In order to carry out the functional test of the output
(arm/disarm), press the key with the number of specified output. By repeatedly pressing the
same key the output status will be toggled to the opposite one. Activation/deactivation of an
output is acknowledged by three short beeps.
Additionally, the function makes it possible to check operation of the LEDs in all keypads
connected to the control panel. Press the key [0] when the function is active to light up all the
LEDs (indicators and keypad illumination) which were unlit at the given moment. Press any
key with another digit number to extinguish the LEDs which were turned on for the duration of
the test.
After quitting the function key [#] or [
*
], the control panel will restore the previous status of the
outputs, from before calling the function.
6.13 S
ERVICE ACCESS
[CODE][
*
][12][#]
The function, which is available to the master user, allows the installer to access the system
by using the service code. It requires some data – i.e. the time period during which the
service mode of the control panel will be available to the installer (service). After expiry of the
preprogrammed time, the access will be blocked, except when the value 99 is set, which
makes permanent the service mode access by using the code (default setting). In order to
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-5 in the language / languages: English as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-5

Satel CA-5 Additional guide - English - 20 pages

Satel CA-5 Quick start guide - English - 12 pages

Satel CA-5 Installation Guide - English - 27 pages

Satel CA-5 Additional guide - German - 20 pages

Satel CA-5 User Manual - German - 24 pages

Satel CA-5 Installation Guide - German - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info