699607
12
Zoom out
Zoom in
Previous page
1/24
Next page
U
SER
M
ANUAL
CA-5
10
set are indicated by the number of a lit up LED, whereas troubles relating to the second set
are indicated by the number of an extinguished LED (one of five).
The previous (earlier) troubles are available for readout by consecutively pressing any key of
the keypad, except for the [
*
] key which cancels the trouble memory review function.
5.3 C
URRENT TROUBLE CHECK
-
OUT
[7]
When the control panel signals a trouble detection (the [TROUBLE] LED is blinking),
holding down the [7] key (until you hear a single beep) will activate the Current Trouble
Check-out Function. On activating the function, the [PROGRAM] LED will start blinking,
and the LEDs 1 to 5 will indicate any possible troubles from the first set (list of troubles as per
the table). Pressing any key (except for the [
*
] key) will change the set of displayed troubles
to the other one, which will be signaled by two short beeps. Consecutive pressing of any key
will display information, alternately, on the first set of troubles and on the second one.
Pressing the [
*
] key will quit the function.
The meaning of the LEDs is as follows:
LED No. FIRST SET OF TROUBLES
1 230V AC power supply loss
2 Battery trouble
3 OUT1 output trouble
4 Power supply outputs trouble
5 Clock loss
SECOND SET OF TROUBLES
1 No voltage on telephone line
2 Problem with access to settings memory
3
Wrong communication codes (connections from
computer blocked for 30 minutes by the panel)
4 Monitoring trouble
5 Dialing error
Note: During the trouble memory review, the extinguished LED No. 3 (a second set
trouble) means „Unsuccessful DWNL (downloading)”. The meaning described in the
table refers to the current trouble check-out only.
5.3.1 Description of some trouble signaling causes
230V AC power supply loss
- the control panel is fitted with a backup power supply to enable
a limited time operation without the mains supply; if the AC loss is indicated despite the electrical
installation being OK, you should call the service.
Battery trouble
– means that the battery voltage is too low (lower than 12V under load). This
condition may hold for several hours after AC supply loss (or after connecting a discharged
battery). The battery charging time depends on its capacitance (the battery is charged with direct
current of approx. 350mA, the time necessary for testing the battery status is about 12 minutes).
Overload OUT1 output
– overload (installation short-circuiting) – usually requires intervention of the
service personnel.
Overload power outputs
– information on the installation fault, requires intervention of the service
personnel (it can be only displayed during the trouble memory review).
Clock loss
– occurs on disconnecting the power supply and restarting the control panel; the clock and
date should be set with the user function 6.
No voltage on telephone line
– means cut-off of the telephone line; it may be also caused by
lifting the handset of the telephone connected to the same line for longer than the time specified by
the installer.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-5 in the language / languages: English as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-5

Satel CA-5 Additional guide - English - 20 pages

Satel CA-5 Quick start guide - English - 12 pages

Satel CA-5 Installation Guide - English - 27 pages

Satel CA-5 Additional guide - German - 20 pages

Satel CA-5 User Manual - German - 24 pages

Satel CA-5 Installation Guide - German - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info