699607
15
Zoom out
Zoom in
Previous page
1/27
Next page
CA-5 SATEL
13
The tamper contact (NC) of the keypad should be connected with the system tamper circuit.
Where two keypads are connected in parallel, the (TMP) tamper contacts should be
connected in series, and the other keypad wires – in parallel.
IMPORTANT: If one of the system zones has been programmed as 24
H TAMPER
and used
for protection of the system elements against tamper, thus creating an
tamper circuit, violation of such a zone will trigger no alarm if the control
panel is in the service mode. If the control panel gives an alarm at the
moment of exiting the service mode, it can mean violation of the tamper line
(opening of one of the contacts).
4.4 C
ONNECTION OF DETECTORS
The circuit connected to the EOL configured zone is to be closed with a 2.2 k resistor.
In case of 2EOL zone, the detector output is to be closed with two 1.1 k resistors. This type
zones (2EOL) allow the control panel to simultaneously monitor the status of detector and its
tamper contact (see Figure 10).
The NO and NC detectors in 2EOL configuration can be connected in the identical way, it is
only important to indicate to the control panel what type of detector is connected to the zone
(2EOL/NO or 2EOL/NC). The same is the case with the detectors having no parameter.
The AUX output is intended to be used for powering the detectors. Separation of the detector
power supply common and the zone common permits eliminating the adverse effect of the
wiring resistance. Assuming that the cable is not very long and that it has just one detector
connected, it is possible to make the installation simpler by leading the power supply
common wire and the signal common wire in one conductor.
Notes:
The real system tamper circuit should also include the tamper contacts of keypad, sirens,
control panel housing, etc.
TMPTMPCOM
KPD CLK DTA
LED-S KEYPAD
TO TAMPER
CIRCUIT
COM CLK DTA KPD
+ OUT1- OUT2 OUT3 AUX KPD DTA CLK COM Z1 Z2 COM Z3 Z4 COM Z5 TIP RING T-1 R-1
AC AC
18V
CA-5
KLCD-S KEYPAD
TO TAMPER
CIRCUIT
Figure 6. Connecting LED and LCD keypads to control panel.
TMP TMP
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-5 in the language / languages: English as an attachment in your email.

The manual is 0,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-5

Satel CA-5 Additional guide - English - 20 pages

Satel CA-5 User Manual - English - 24 pages

Satel CA-5 Quick start guide - English - 12 pages

Satel CA-5 Additional guide - German - 20 pages

Satel CA-5 User Manual - German - 24 pages

Satel CA-5 Installation Guide - German - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info