699583
3
Zoom out
Zoom in
Previous page
1/20
Next page
SECURITY SYSTEM...........................................................................................
USER ..................................................................................................................
TELEPHONE NUMBER ......................................................................................
ADDRESS...........................................................................................................
REMARKS...........................................................................................................
............................................................................................................................
The mode of operation of the alarm control panel is defined by the security system
parameters. Changing these parameters makes it possible to adapt the panel operation to
individual needs of the protected site. The initial settings, or the so-called „defaults”, are
indicated in the description of each service function.
The service functions allow changes in the settings of particular system parameters to be
made by means of the keypad. Such changes can only be made when the control panel is
not armed and when it signals no alarm.
The parameters can also be changed remotely by means of the computer and the DLOAD10
program. In order to do so, the „downloading” (DWNL) function of the control panel must be
used (see description in the CA-5
I
NSTALLER
M
ANUAL
). The program makes it possible to
assign names to the users and zones. Such names will be displayed when viewing the
memory log in the LCD keypad or on the computer screen.
ACTIVATION OF SERVICE MODE
To change any parameter by means of the service function, activate the service mode in the
control panel ([SERVICE CODE] [#]), enter the number of the corresponding service function
and press the [#] key. The numbers and descriptions of functions are included hereunder in
this manual.
It is also possible to call the service mode without entering the service code. With this aim
you should:
disconnect the control panel power supply (first the mains, then the battery),
put a jumper on the RESET pins on the control panel mainboard,
reconnect the control panel power supply: first the battery, then the mains – the LED
keypad will start blinking with all its LEDs and generating short beeps; the LCD keypad will
display a “No CLK signal” massage and generate short beeps,
remove the jumper – the keypads will confirm the panel entering the service mode by four
short and one long beeps; in the LED keypad, the [
PROGRAM
] diode will light up; in the
LCD keypad, the service mode menu will display.
This procedure is colloquially known as the entry „from pins” (see: description of function FS 9).
PROGRAMMING WITH LED KEYPAD
Having called the service function, check the current setup or enter new data. The way of
data entry is described in subsequent sections. Press [#] in order to memorize the new
setting of a parameter, or press [
*
] and hold down until you hear two long beeps, or,
alternatively, press in turn [
*
][#] to quit the function without making any changes.
Checking the setup of numeric parameters (which require numbers to be entered) is possible
by double pressing the [
*
] key. Displayed in the binary system on the LEDs (2–5) are
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-5 Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-5 Plus in the language / languages: English as an attachment in your email.

The manual is 0,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-5 Plus

Satel CA-5 Plus User Manual - English - 24 pages

Satel CA-5 Plus Installation Guide - English - 27 pages

Satel CA-5 Plus User Manual - German - 24 pages

Satel CA-5 Plus Additional guide - German - 20 pages

Satel CA-5 Plus User Manual - German - 24 pages

Satel CA-5 Plus Installation Guide - German - 28 pages

Satel CA-5 Plus User Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info