699583
6
Zoom out
Zoom in
Previous page
1/27
Next page
Installer Manual CA-5
4
1 –
BURGLARY ALARM
(with the operating time equal to zero, the output is active until
clearing the alarm, e.g. visual indication)
2 –
KEYPAD ALARM
3 – READY
STATUS
(active when none of the zones is violated)
4 –
ARMED STATUS
5 –
INDICATOR OF
AC,
BATTERY OR TELEPHONE LINE TROUBLE
6 – AC
LOSS INDICATOR
7 –
BATTERY TROUBLE INDICATOR
8 –
TELEPHONE LINE TROUBLE INDICATOR
9 – GROUND
START
SIGNAL
(the signal of 2-second duration which occurs before "lifting
the handset" by the control panel and which is required by a specific type of
telephone exchange)
10 –
TELEPHONE LINE RELAY
(description see p. 17)
11 – MONO
SWITCH
(control type, activated for a specified time period with the user
function 7)
12 – BI
SWITCH
(control type, switched over permanently with the user function 8)
13 – RESETTABLE
POWER
(deactivated with the user function 9 for a time period
programmed as the output cutoff time – minimum 4 seconds)
14 – DURESS
ALARM
(signals disarming or alarm clearing with the use of a "duress" code)
15 –
MONITORING ACKNOWLEDGEMENT
(activated by the control panel for 3 seconds after
correctly ending communication with the monitoring station)
16 –
PARTIALLY ARM STATUS
(active when the armed mode is on with zones bypassed)
The number of output function corresponds to the number programmable in the FS 48 and
FS 50 service functions to determine the output function.
The OUT2 and OUT3 outputs in the active state will short-circuit the terminal to ground.
It is possible to alter the way of work of outputs. You can change polarization of the terminals
-OUT1, as well as OUT2 and OUT3 (FS 84 options 1, 2 and 3). By selecting the „Polarization
OUTn reversed” option (n – output number), the terminal will be shortened to the common in
its inactive state and cut off in the active state.
The following parameters can be programmed for the outputs:
alarm signaling time (FS 47)/cutoff time of FS 49 and FS 51 outputs,
burglary alarm signaling delay (FS 46, FS 82 and FS 83).
The output OUT1 is designed to signal the burglary and fire alarms. The installer can select
the identical signaling mode for the fire alarm and for the burglary alarm (FS 84 option 4),
however, the signaling delay (if any) will only apply to the burglary alarm.
The installer can activate the signaling of arming/disarming and alarm clearing on the OUT1
output (FS 84 option 5).
The power supply outputs for the detectors (AUX) and keypad (KPD) have a common
polymer fuse, limiting the current consumption from the power supply by the external devices
to 350 mA.
All the outputs are protected against inductive loads and impulse interference.
3.3 LED
KEYPAD
In the LED keypad basic information concerning the system status is provided by means of
light emitting diodes LED (for detailed description, see the user manual). Displayed are the
status of zones and system (supervision, alarm), information on power supply status,
detection of emergency situation and operation in programming mode.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-5 Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-5 Plus in the language / languages: English as an attachment in your email.

The manual is 0,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-5 Plus

Satel CA-5 Plus Additional guide - English - 20 pages

Satel CA-5 Plus User Manual - English - 24 pages

Satel CA-5 Plus User Manual - German - 24 pages

Satel CA-5 Plus Additional guide - German - 20 pages

Satel CA-5 Plus User Manual - German - 24 pages

Satel CA-5 Plus Installation Guide - German - 28 pages

Satel CA-5 Plus User Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info