699577
21
Zoom out
Zoom in
Previous page
1/43
Next page
CA-10 Installer Manual 19
Setting keypad addresses
The address is keypad's additional tamper protection. A different (arbitrary) address
should be set in each keypad. To set an address in LED keypad, put jumpers on
corresponding pairs of the ABCD pins (see figures: 3, 4 and description of the service
function FS111). In LCD keypad, the address must be programmed. The programming
consists in entering four digits in binary code (by analogy with the LED keypads: 1=pins
shorted, 0=pins open). The control panel does not support LED keypads in which either all
jumpers or no jumpers are set, as well as LCD keypads in which the address 0000 or 1111
has been programmed. The address is stored in the panel EEPROM (non-volatile) memory,
together with the other system parameters.
The LCD-keypad address can be changed in two ways:
1. Directly (skipping the service code):
Disconnect the keypad power supply and the data bus wires (CLK, DATA).
Short-circuit the CLK and DATA terminals of the keypad.
Switch on the keypad power supply. The following text will be displayed: „Keypad
hardware address: 1001” (the default value, corresponding to the jumpers read out in
the ABCD sequence).
Using the [0] and [1] keys, enter the proper address and then press the [#] key.
The „Address set” text will be displayed on the keypad.
Connect the keypad to the control panel in appropriate way (CLK, DATA).
2. By means of the keypad service functions:
Activate the control panel service mode.
Select in turn the items in menu of displayed functions: LCD keypad; Settings;
Keypad address.
Using the [0] and [1] keys, enter the proper address and then press the [#] key.
The keypad will display the text: „Set addresses (FS124) ? 1=Yes”.
Press the [1] key to automatically perform the FS124 service function and save the
settings.
Note: For correct handling of the LCD keypads by the CA-10 control panel, the FS124
function must be performed on each of the LCD keypads connected to the panel.
It may turn out on starting the control panel that the keypad is not supported (no reaction to
pressing the keys). A message appears then on the LCD keypad display that there is no
communication with the control panel. This is usually because the keypad address is different
than the one programmed in the panel. Depending on whether other keypads are also
connected to the panel, or this keypad is the only one in the system, you can follow either of
the two ways:
3. Call the service mode in another keypad and start the FS124 service function, which will
result in correct keypad addresses being automatically read out by the control panel.
In this case, remember to start the FS124 service function in all LCD keypads connected
to the panel.
4. Enter the service mode by means of jumpers and program a correct keypad address in the
control panel (see: Starting the Control Panel).
Connection of zone expander
In order to increase the number of zones, a zone expander can be connected, instead of
a full set of keypads. It makes available the zones of keypads required for full configuration.
The expander should be connected as a next keypad. It can be used in combination with
a different number of keypads. For details regarding the connection see the expander
installation manual.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 60 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 User Manual - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info