31127
5
Zoom out
Zoom in
Previous page
1/16
Next page
5
INSTALLATION
Placing your VCR on top of or under the TV receiver may
result in interference on the TV screen when the VCR is
on. If this occurs, move the VCR to a position beside the
TV receiver.
AUDIO
LINE1(AUX1)
R
L
IN
IN
OUT
OUT
ANT.IN
VIDEO
VHF/UHF
/CATV
Cable/
Antenna
R-AUDIO-L
VIDEO
IN
OUT
IN
OUT
RF OUT
When using the RF coaxial cable (Supplied)
Connect the 75-ohm Coaxial Cable to RF OUT
(VHF/UHF/CATV) on the VCR. Connect the other end to the 75-
ohm antenna input on the back of the TV.
When using the Audio/Video cable (Not supplied)
If your TV has A/V input jacks, you can connect your VCR’s
AUDIO/VIDEO jacks to the back of your TV.
Direct audio/video connections usually result in better picture
and sound quality for tape playback. Please see your TV’s
owners manual for details on how to set your TV to the VIDEO
mode using the TV/VIDEO button on your TV.
VCR Output Channel Setting
1.
Set the TV to the VCR channel (3 or 4).
2. While the VCR is turned off,
press and hold CHANNEL
(V/v) on the front panel for more than five seconds.
Indicators on the INDICATOR PANEL blinks as follows:
3.
Use CHANNEL (V/v) on the front panel to change the
RF output channel (CH 03 or CH 04).
4.
Turn the VCR off and then on again.
VCR TO TV CONNECTION
ANTENNA TO VCR CONNECTIONS
AUDIO
LINE1(AUX1)
R
L
IN
IN
OUT
OUT
ANT.IN
VIDEO
VHF/UHF
/CATV
IN
OUT
RF OUT
Without Cable Box
If your cable wire is connected to your TV without a converter or
descrambler box, unscrew the wire from your TV and attach it to
the ANT.IN connector on the VCR. Use the supplied round
coaxial cable to connect the VCR’s RF OUT (VHF/UHF/CATV)
connector and the 75 ohm antenna input connector on the TV.
With this connection, you can receive all midband, super band,
and hyperband channels.
With Cable Box
If a converter is required in your cable system, follow the instruc-
tion below.
The cable hookup permits both TV and VCR operation.
To view or record a CATV channel
1 Set the TV to the VCR channel (3 or 4).
2 Set the VCR channel selector to the output channel of the
Cable Converter box by pressing the CH/TRACK (v/V) or the
number buttons (0-9) of your VCR. (Example: CH3).
3 Select the channel to view on the Cable Converter Box.
•With this connection, you CANNOT record one program while
viewing another.
Channel memory programming is not needed when using this
connection.
NOTES
1
Disconnect the antenna leads from the rear of the TV receiver.
2 Identify the type of cable from your antenna. If it is a round
cable as illustrated, it is a 75 ohm coaxial antenna cable. This
cable will connect directly to the connector marked ANT.IN on
your VCR.
If your antenna lead wire is a flat type antenna cable, connect
it to a Antenna Adaptor (300-ohm to 75-ohm) (not supplied)
and slip the Adaptor onto the ANT.IN connector. The Adaptor
does not screw on to the VCR, it just slips over the connector.
(CH 03)
(CH 04)
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo VWM900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo VWM900 in the language / languages: English as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info